Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Washing machine not spinning or shaking violently: what to check

Easy20–45 minutesReviewed By the MelbourneFix team

The short answer

Most spin problems come down to an unbalanced load, a machine that is not level, or water that has not drained. Fix those three and a repairer is only needed for worn belts, bearings or suspension.

Modern washing machines are cautious. If the drum senses a lopsided load, or the water has not fully drained, the machine will slow the spin or skip it altogether to protect itself. So soaking wet clothes do not always mean something is broken.

Violent shaking is the other side of the same problem. A machine that bangs against the wall or creeps across the floor is either badly loaded, standing unevenly, or has worn suspension parts that can no longer hold the drum steady.

The checks below sort the simple causes from the mechanical ones. None of them need the machine opened up.

Likely causes, most common first

  • Unbalanced or overloaded drum

    DIY

    Problem happens with some loads and not others, especially single heavy items such as a doona, bath mat or pair of jeans.

  • Machine not level

    DIY

    Machine rocks when you push on a top corner. Often starts after a move or a new floor.

  • Water has not drained

    DIY

    Clothes are sitting in water, not just wet. The spin will not start until the drum is empty.

  • Transit bolts left in (new or recently moved front loaders)

    DIY

    Extreme shaking and banging from the very first wash after delivery.

  • Worn drive belt, suspension or shock absorbers

    Professional

    Drum does not turn at all or turns weakly, burning smell, or the drum drops and bangs even with a small, even load.

  • Worn drum bearings

    Professional

    Loud rumbling or roaring on spin that has grown worse over months. The drum has play if you lift its inner rim.

Before you start

Safety first

  • Switch off at the power point and unplug before tilting or moving the machine.
  • Washing machines are heavy, often 60–80 kg. Get a second person to help you tilt or shift one, and keep fingers clear of the feet.
  • Never reach into a drum that is still turning, and never try to defeat the lid or door lock to watch the spin.
  • A burning rubber smell means stop the cycle and leave the machine off until it has been looked at.

What you will need

  • Spirit level, or a level app on your phone
  • Adjustable spanner or the spanner supplied with the machine
  • Torch

Step-by-step checks

  1. Step 1: Redistribute the load and try again

    Open the machine and spread the washing evenly around the drum. Untangle sheets that have balled up and separate heavy items from light ones.

    A single heavy item is the hardest load to balance. Add a couple of towels to a lone bath mat or doona cover so the weight can spread. Then run a spin-only cycle.

    Tip: As a rough guide, a full load should still leave a hand's width of space at the top of a front loader's drum.

  2. Step 2: Confirm the water has drained

    If there is standing water in the drum, the machine has a drain problem rather than a spin problem. Select a drain cycle and listen for the pump.

    If the water stays put, follow our guide to a washing machine that is not draining before going any further here.

  3. Step 3: Check the machine is level and all four feet are firm

    Place a spirit level on top of the machine, front to back and then side to side. Press down on each top corner in turn. Any rocking means one foot is not carrying weight.

    The front feet, and on many machines the rear ones too, screw in and out. Loosen the lock nut against the cabinet, wind the foot until the machine sits level and solid, then tighten the lock nut back up against the cabinet so the foot cannot work loose again.

    Careful: Skipping the lock nut is the most common reason a levelled machine starts walking again a few weeks later.

  4. Step 4: Look for transit bolts on a new or relocated front loader

    Front loaders are shipped with three or four long bolts through the back panel that clamp the drum for transport. If they are still fitted, the drum cannot float on its springs and the whole machine will shake violently.

    Check the back of the machine with a torch. The bolts are usually marked and sit in coloured plastic spacers. Undo them with the supplied spanner, pull out the spacers and fit the blanking caps. Keep the bolts in case you move house.

  5. Step 5: Check what the machine is standing on

    Springy timber floors, especially in older Melbourne weatherboards, amplify spin vibration. So do stacked plinths that are not designed for the machine.

    A sheet of thick plywood screwed to the floor joists spreads the load. Anti-vibration pads under the feet help on tiles and concrete. Do not put a front loader on wheels or a wheeled trolley.

  6. Step 6: Listen to an empty spin

    Run a spin cycle with the drum empty. An empty drum should run up to speed smoothly with a steady whirr.

    A deep rumble that gets louder with speed points to worn bearings. A drum that barely turns, a squeal, or a smell of hot rubber suggests the belt. Repeated banging with nothing in the drum means worn suspension. All three need a repairer.

When to stop and call a repairer

  • The drum does not turn at all, even though the machine drains and you can hear the motor trying.
  • There is a burning smell, or black rubber dust under the machine.
  • The machine bangs on spin with an empty or lightly loaded drum.
  • Spin noise has become a loud roar, or you can see rust-coloured streaks down the back of the outer tub.
  • An error code returns on every spin attempt after you have rebalanced and levelled the machine.

Filters, hoses and seals are yours to clean and check. Anything behind a screwed-on panel carries mains voltage and is a job for an appliance technician. Heat pump dryers also contain refrigerant, which only a licensed technician may handle.

What it costs

Doing it yourself
$0 for rebalancing and levelling. Anti-vibration pads are around $15–$30 a set.
Professional repair
$200–$450 for most washing machine repairs including the call-out. Bearing replacement on a front loader is a long job and is often quoted well above that range.

Indicative figures from Australian repair cost guides. Always ask for a firm quote after diagnosis, and whether the call-out fee is credited against the repair. See our Melbourne repair cost guide for more.

Repair or replace?

Belts and suspension parts are generally worth doing on a machine in otherwise good order.

Bearings are the big decision. On many front loaders the bearings are pressed into a sealed outer tub, so the repair means replacing the whole tub assembly. On a machine that is eight or more years old, the quote can approach the price of a replacement, and at that point a new machine with a fresh warranty is usually the better use of the money.

If you do replace it, the old machine is e-waste and cannot go in landfill in Victoria. Many retailers will take the old one away on delivery, and council transfer stations accept whitegoods.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Why does my washing machine only shake on the final spin?

The final spin is the fastest, often 1,000 to 1,400 rpm on a front loader, so any imbalance that was tolerable at lower speed becomes obvious. Uneven loading and feet that are not locked are the usual causes.

Is it bad to keep using a machine that shakes?

Yes. Heavy vibration wears the suspension and bearings faster, can loosen hose connections and may damage the floor. It is worth sorting out promptly.

My top loader stops and fills with water again before spinning. Is that a fault?

Usually not. Many top loaders deliberately refill and agitate to redistribute a lopsided load before trying the spin again. If it does this repeatedly, rearrange the load by hand.

Can I replace a drive belt myself?

It is possible on some models, but it means removing the back panel of a mains-powered appliance. We recommend leaving it to an appliance repairer, who will also check why the belt failed.

Melbourne repairers for washing machines & dryers

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Optimum Electronic Solutions

Shopfront & mobile

31 Prime St, Thomastown VIC 3074

Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.

Woolley Appliance Services

Shopfront & mobile

10 Freight Rd, Ravenhall VIC 3023

Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.

Authorised Samsung and LG service centre. Second workshop in Clayton.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

See all laundry repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More laundry guides