Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Washing machine not draining: how to find and clear the blockage

Easy30–60 minutesReviewed By the MelbourneFix team

The short answer

In most cases a washer that won't drain has a blocked pump filter or a kinked drain hose, and both are jobs you can do yourself in under an hour with a towel and a shallow tray.

A drum full of grey water at the end of a cycle looks like a disaster, but it is one of the most fixable washing machine faults. The machine drains by pumping water through a small filter, up a corrugated hose and into your laundry trough or standpipe. A blockage at any of those three points stops the lot.

Coins, hair ties, bobby pins and the odd baby sock are the usual culprits. Front loaders collect them in a filter behind a small flap at the bottom of the machine. Many top loaders have no user-accessible filter, so the checks there are mostly about the hose and the drain it empties into.

Work through the steps below in order. They start with the things that cost nothing and need no tools, and they stop before anything that involves taking panels off the machine.

Likely causes, most common first

  • Blocked pump filter

    DIY

    Machine hums at the drain stage but little or no water leaves. Common after washing pockets full of tissues or coins.

  • Kinked or blocked drain hose

    DIY

    Machine was recently moved or pushed back hard against the wall. Water may drain slowly rather than not at all.

  • Blocked standpipe or laundry trough waste

    DIY or professional

    Water backs up out of the standpipe or trough and runs onto the floor when the machine pumps out.

  • Failed drain pump

    Professional

    Filter and hose are clear but the pump is silent, or it makes a loud grinding or rattling noise.

  • Lid switch, door lock or control fault

    Professional

    Machine stops mid-cycle with an error code and will not advance to drain or spin at all.

Before you start

Safety first

  • Switch the machine off at the power point and pull the plug out before you touch the filter or hoses. Water and mains power in the same small space is the real hazard here.
  • If the cycle was a hot wash, wait at least 30 minutes. Water trapped in the drum can still be hot enough to scald.
  • Expect several litres of water from the filter on a front loader. Have towels down and a shallow tray ready before you open it.
  • Do not remove the back or top panels to reach the pump. If the fault is inside the cabinet, that is the point to call a repairer.

What you will need

  • Old towels and a shallow baking tray or takeaway containers
  • Bucket
  • Flat-head screwdriver or coin (for the filter flap)
  • Long-nose pliers
  • Torch
  • Old toothbrush

Step-by-step checks

  1. Step 1: Run a drain or spin-only cycle

    Before pulling anything apart, select the drain or spin-only program and listen. A healthy pump makes a steady low hum and you will hear water rushing down the waste within a few seconds.

    If the machine drains normally this time, the original cycle may simply have been interrupted by a power blip or an unbalanced load. If you hear the pump humming but no water moves, suspect a blockage. If you hear nothing at all, the pump or its control may have failed.

    Tip: Write down any error code on the display. Brands such as Bosch, LG, Samsung and Fisher & Paykel use specific codes for drain faults, and a repairer will ask for it.

  2. Step 2: Check the drain hose for kinks

    Switch off and unplug the machine, then ease it forward far enough to see behind it. Follow the grey corrugated hose from the back of the machine to where it hooks into the trough or standpipe.

    Straighten any sharp bends and make sure the machine is not sitting on the hose. The end should hook over the trough or sit loosely in the standpipe, not be jammed down it. Pushing the hose too far down creates a siphon and can also block the flow.

  3. Step 3: Make sure the house drain is not the problem

    Tip a bucket of water down the laundry trough or standpipe. If it backs up or drains slowly, the blockage is in your plumbing rather than the machine.

    Lint build-up in a trough waste can often be cleared by removing the plug-hole grate and pulling the lint out by hand. A blockage further along is a job for a licensed plumber.

  4. Step 4: Drain the machine and clean the pump filter (front loaders)

    Open the small flap at the bottom front corner of the machine. Most models have a short emergency drain tube next to the round filter cap. Pull the tube out, hold it over your tray, remove its bung and let the water run. You will need to empty the tray several times.

    Once the flow stops, turn the filter cap anticlockwise and pull it out. Remove whatever is caught in it, rinse it under the tap and scrub the threads with an old toothbrush.

    Shine a torch into the filter housing. You should see the small pump impeller at the back. Check that it turns freely with a gentle push and that nothing is wrapped around it. Refit the filter, turning it clockwise until it is firmly seated.

    Careful: A filter that is not fully tightened will leak onto the floor during the next wash. Run a short rinse cycle and watch the flap area before you push the machine back.

  5. Step 5: Flush the drain hose

    If the filter was clean, unhook the drain hose from the trough, lower the end into a bucket and see whether water flows out under gravity. No flow suggests a blockage in the hose itself.

    On most machines the hose can be unclipped at the wall end and flushed with a garden hose outside or under the laundry tap. A build-up of grey sludge from detergent and fabric softener is common in older hoses.

  6. Step 6: Test with an empty cycle

    Reconnect everything, plug the machine back in and run a rinse and spin with the drum empty. Watch the hose outlet. You should see a strong, steady stream when the machine pumps out.

    If it now drains, run a hot maintenance wash with nothing in the drum to clear any remaining residue.

When to stop and call a repairer

  • The filter and hose are clear but the pump is silent or noisy when the machine should be draining.
  • The machine trips the safety switch in your switchboard when it reaches the drain stage.
  • You can see water leaking from underneath the cabinet rather than from the filter or hose.
  • The same error code returns after you have cleared the filter and the hose.
  • Your machine is a top loader with no accessible filter and the hose and house drain are both clear.

Filters, hoses and seals are yours to clean and check. Anything behind a screwed-on panel carries mains voltage and is a job for an appliance technician. Heat pump dryers also contain refrigerant, which only a licensed technician may handle.

What it costs

Doing it yourself
Usually $0. A replacement drain hose is around $20–$40 if yours is split.
Professional repair
$200–$450 for a typical washing machine repair including the call-out, with a drain pump replacement usually sitting in the middle of that range.

Indicative ranges from Australian repair cost guides. Call-out fees of $80–$200 are common in Melbourne and are often credited against the repair if you go ahead. See our Melbourne repair cost guide for more.

Repair or replace?

A drain fault on its own is rarely a reason to replace a washing machine. A new pump is a modest repair on a machine that is otherwise working well.

It becomes a closer call when the machine is more than about eight to ten years old and has other problems, such as a noisy drum bearing or a rusting cabinet. A common rule of thumb is to think twice when a repair quote is more than half the price of an equivalent new machine.

If the machine is only a few years old, check your rights before paying anyone. Under the Australian Consumer Law a washing machine is expected to last a reasonable time, which can be longer than the manufacturer's warranty.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Can I open the door of a front loader that is full of water?

Not until the water level is below the door. Most front loaders keep the door locked while there is water in the drum. Drain it through the emergency tube or the filter first, then wait a couple of minutes for the lock to release.

How often should I clean the pump filter?

Every two to three months is a sensible habit, and straight away if you know something has gone through the wash in a pocket. Your manual will give the manufacturer's interval.

My top loader has no filter. Where does the lint go?

Many modern top loaders flush lint out with the drain water or use a self-cleaning filter under the agitator. If yours has a removable lint filter, it is usually a mesh bag or cartridge inside the agitator column or on the rim of the bowl.

Is it safe to bail the water out by hand?

Yes, with the machine unplugged. On a top loader you can bail with a jug and soak up the rest with towels. It is slow, but it lets you get the washing out while you wait for a repairer.

Melbourne repairers for washing machines & dryers

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Optimum Electronic Solutions

Shopfront & mobile

31 Prime St, Thomastown VIC 3074

Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.

Woolley Appliance Services

Shopfront & mobile

10 Freight Rd, Ravenhall VIC 3023

Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.

Authorised Samsung and LG service centre. Second workshop in Clayton.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

See all laundry repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More laundry guides