Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Clothes dryer not heating: safe checks before you call a repairer

Easy20–40 minutesReviewed By the MelbourneFix team

The short answer

A dryer that tumbles without drying is very often choked with lint or has tripped its safety thermostat because of poor airflow. Clean the filter, the vent path and the condenser or heat pump filter before assuming the element has failed.

A dryer needs two things to work: heat and moving air. Take away the airflow and the heat has nowhere to go, so a safety thermostat cuts the heater to prevent a fire. From the outside it looks like the heater has died, when the real problem is a few dollars' worth of lint.

Australia has three common dryer types and they fail differently. Vented dryers blow hot, damp air out of the front or through a wall duct. Condenser dryers collect water in a tank. Heat pump dryers, now the most common choice for efficiency, use a sealed refrigerant circuit instead of an element and rely on very clean filters.

Lint is also a genuine fire risk, so even if these checks do not solve the fault, they are worth doing.

Likely causes, most common first

  • Lint filter blocked or coated with residue

    DIY

    Cycles take longer and longer. Filter looks clean but water pools on the mesh instead of running through it.

  • Blocked vent duct or poor room ventilation

    DIY

    Laundry becomes hot and steamy, the top of the dryer is very hot to touch, or the cycle cuts out early.

  • Clogged condenser or heat pump filter

    DIY

    Condenser or heat pump model shows a filter or cleaning warning, or the water tank stays almost empty.

  • Tripped thermal cut-out

    Professional

    Dryer tumbles with completely cold air after a period of poor airflow.

  • Failed heating element or thermostat

    Professional

    Airflow is good and filters are clean, but the air stays cold from the start of every cycle.

  • Heat pump or sensor fault

    Professional

    Heat pump dryer shows an error code and stops, or runs for hours without drying.

Before you start

Safety first

  • Switch off at the power point and unplug the dryer before cleaning anything beyond the lint filter.
  • Let the dryer cool for 30 minutes after a cycle. The drum and the area around the element stay hot.
  • Do not remove the rear or side panels. The heating element, thermostats and wiring carry mains voltage and are not user-serviceable.
  • A heat pump dryer contains refrigerant in a sealed system. Only a technician with a refrigerant handling licence may work on that circuit.
  • Never run a dryer with the lint filter removed.

What you will need

  • Vacuum cleaner with a brush attachment
  • Soft brush or old paintbrush
  • Mild detergent and warm water
  • Torch

Step-by-step checks

  1. Step 1: Rule out the settings

    Check that the dryer is not on an air, cool or freshen-up program, and that a low heat or delicate option has not been left on. On sensor models, a very small load can end early because the sensors do not register damp fabric.

    Check the washing too. If the washing machine's spin is weak, clothes go into the dryer carrying far more water than it is designed to remove.

  2. Step 2: Clean the lint filter properly

    Pull the filter out and peel the lint off. Then hold it under a running tap. Water should pass straight through the mesh. If it beads and pools, the mesh is coated with fabric softener or dryer sheet residue that you cannot see.

    Wash the filter in warm water with a little dish detergent, scrub gently with a soft brush, rinse and let it dry completely before refitting.

    Tip: Vacuum the slot the filter sits in. A surprising amount of lint gets past the mesh and collects underneath.

  3. Step 3: Check the airflow path on a vented dryer

    With the dryer running on a heat setting, hold your hand near the vent outlet. You should feel a strong stream of warm, damp air. Weak flow means a restriction.

    If the dryer is ducted outside, unplug it, disconnect the flexible duct and check it for lint, kinks and crushed sections. Check the outside wall vent as well. Flaps stick shut and wasps like to nest in them.

    If the dryer vents into the room, it needs an open window or door. In a closed laundry the air quickly becomes saturated and nothing will dry.

  4. Step 4: Clean the condenser or heat pump filter

    On a condenser dryer, open the lower front panel, release the catches and slide the condenser unit out. Rinse it through with a tap or shower head until the water runs clear, let it drain and refit it.

    On a heat pump dryer, open the lower panel and remove the secondary foam or mesh filter. Wash it according to the manual and let it dry. The fine metal fins behind it should only ever be cleaned gently with a soft brush or a vacuum brush attachment, because they bend easily.

    Empty the water tank, or check that the drain hose is not kinked if your dryer is plumbed to a drain.

    Careful: Do not poke at the heat pump's fins or pipework with anything sharp. Puncturing the sealed circuit turns a cleaning job into an uneconomic repair.

  5. Step 5: Run a timed test

    Reassemble everything and run a timed, high-heat cycle with a few damp towels. After ten minutes, pause the cycle and open the door. The towels and the drum should be clearly warm on a vented or condenser dryer.

    A heat pump dryer runs cooler by design, so expect warm rather than hot. What matters is that the towels are noticeably drier after 30 to 40 minutes.

When to stop and call a repairer

  • The air is cold from the start of every cycle even though filters and vents are clean.
  • The dryer trips the safety switch or a circuit breaker.
  • You smell burning, or see scorch marks on clothes or around the door.
  • A heat pump dryer shows a persistent error code or runs for hours without drying.
  • The drum does not turn, or there is a loud scraping or thumping noise.

Filters, hoses and seals are yours to clean and check. Anything behind a screwed-on panel carries mains voltage and is a job for an appliance technician. Heat pump dryers also contain refrigerant, which only a licensed technician may handle.

What it costs

Doing it yourself
$0 for cleaning. A replacement lint filter is typically $20–$50.
Professional repair
$180–$380 for most dryer repairs including call-out. A heating element replacement is often quoted in the $250–$550 range.

Indicative figures from Australian cost guides, not Melbourne quotes. Heat pump system faults can cost considerably more and should be quoted before work starts. See our Melbourne repair cost guide for more.

Repair or replace?

Basic vented dryers are cheap to buy, sometimes little more than the cost of a call-out and an element. For an older vented dryer, compare the quote against the price of a new one before saying yes.

Condenser and heat pump dryers cost a lot more to replace, so repairing an element, sensor or belt usually makes sense. A failed compressor or a refrigerant leak on a heat pump dryer that is out of warranty is the exception and is often not economic.

A heat pump dryer that fails within its first several years is worth raising with the retailer first. Consumer guarantees under the Australian Consumer Law are not limited to the warranty period.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Why is my dryer taking two cycles to dry a load?

Restricted airflow is the most common reason. Wash the lint filter, clear the vent or condenser, and make sure the washing machine is spinning the load properly beforehand.

Can I reset the thermal cut-out myself?

Some dryers have a reset button behind the rear panel, but reaching it means opening a mains appliance, and a cut-out that has tripped is telling you something is wrong. We recommend having a repairer reset it and check why it operated.

Is a heat pump dryer meant to feel cooler than my old dryer?

Yes. Heat pump dryers work at around 50 degrees Celsius rather than the 70 to 80 degrees of a vented dryer. Cycles are longer but use far less electricity.

How often should the condenser be cleaned?

Check your manual, but once a month is typical for a condenser unit in regular use, and the heat pump filter after every few loads.

Melbourne repairers for washing machines & dryers

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Optimum Electronic Solutions

Shopfront & mobile

31 Prime St, Thomastown VIC 3074

Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.

Woolley Appliance Services

Shopfront & mobile

10 Freight Rd, Ravenhall VIC 3023

Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.

Authorised Samsung and LG service centre. Second workshop in Clayton.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

See all laundry repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More laundry guides