TV won't turn on: what the standby light is telling you
The short answer
A TV that will not turn on is not always a dead TV. A flat remote, a tired power board, a loose mains lead or a set that has locked up in standby all look exactly the same from the couch: you press the button and nothing happens.
The small standby light on the front or bottom edge of the set is the best clue you have. Whether it is off, steady or blinking sorts the problem into three quite different groups, and only one of them definitely needs a repairer.
Everything below is done from outside the TV. None of it involves removing the back cover, and for good reason, which is explained in the safety notes.
Likely causes, most common first
TV locked up in standby
DIYStandby light is on as normal but the set ignores both the remote and its own power button. Often follows a power flicker or a software update.
Remote control fault or flat batteries
DIYStandby light is on and the TV turns on from the button on the set itself, but not from the remote.
Failed power board, power point or mains lead
DIYNo standby light at all, and other devices on the same power board are also dead or behaving oddly.
Failed power supply board
ProfessionalNo standby light with a known good power point and lead, or the TV clicks on and off repeatedly. Common after storms and power surges.
Backlight or main board fault
ProfessionalStandby light blinks in a repeating pattern, or the TV appears to start, sometimes with sound, then shuts itself down within seconds.
Before you start
Safety first
- Never remove the back of a TV. The power supply board holds a dangerous charge in its capacitors even after the set has been unplugged, and there is nothing inside that a household can safely service.
- Switch off at the power point before plugging or unplugging the mains lead at the back of the TV.
- If you smell burning, hear crackling or see scorch marks near the vents or the power inlet, unplug the TV and leave it unplugged.
- Large TVs are awkward and the panel is fragile. If you need to turn a set around to reach the sockets, get a second person and hold it by the frame, never by pressing on the screen.
- If the TV has been hit by a power surge or has had liquid spilled into it, do not keep trying to power it up.
What you will need
- Fresh batteries for the remote
- A lamp or phone charger to test the power point
- Mobile phone camera (to test an infrared remote)
- Torch
Step-by-step checks
Step 1: Look at the standby light before you touch anything
Find the small indicator light, usually on the bottom edge or lower corner of the frame. Note whether it is off, on steadily, or blinking, and whether it changes when you press the power button.
Normal behaviour differs between brands. On many sets the light is on in standby and goes out when the TV is running. On others it is the reverse, and some TVs let you turn the standby light off in the settings. What matters is whether it is doing what it usually does.
If the light changes as though the TV has turned on but the screen stays black, the TV is probably running with no picture. That is a different fault, covered in our guide to a TV with sound but no picture.
Tip: If the light is blinking, count the blinks between pauses and write the number down. You will want it later.
Step 2: Prove the power point and bypass the power board
Unplug the TV from its power board and plug it straight into a wall power point. Test that power point with a lamp or phone charger first so you know it is live.
Power boards and surge protectors fail more often than TVs do. A surge-protected board can sacrifice itself in a storm and leave some or all of its outlets dead. If the TV works from the wall, replace the board rather than going back to it.
If nothing in the room has power, check your switchboard for a tripped circuit breaker or safety switch before blaming the TV.
Step 3: Reseat the mains lead at the back of the TV
Many TVs use a detachable mains lead that pushes into a socket on the back. It can work loose when the set is moved or the cabinet is cleaned behind. With the power point off, push the lead firmly home, or pull it out and refit it.
Some smaller TVs use a separate power adaptor, a brick in the middle of the lead. If yours does, check both ends are connected and whether the adaptor has an indicator light of its own.
Tip: A detachable figure-8 mains lead is a standard part and cheap to replace. If the lead has been chewed, crushed or kinked, replace it rather than taping it.
Step 4: Do a full power cycle
Switch the TV off at the power point and pull the plug out. Leave it unplugged for at least a full minute. While it is unplugged, press and hold the power button on the TV itself for about 15 seconds, which helps drain any remaining charge from the standby circuit.
Plug the TV back in, switch on at the power point, wait ten seconds, then press the power button on the TV. This clears most software lock-ups and is the single most effective fix for a set that sits in standby and ignores you.
Step 5: Take the remote out of the equation
Use the power button on the TV. It is often hidden under the centre of the bottom edge, behind a lower corner, or on the back near the sockets, and on some models it is a small joystick. If the TV turns on from this button, the fault is the remote.
Fit fresh batteries, not ones borrowed from another device. To test an infrared remote, point it at your phone's camera and press a button. On most phones you will see the emitter flicker on the screen. If one camera shows nothing, try the front-facing one, as some rear cameras filter infrared out.
Many smart TV remotes use Bluetooth for most functions and may need pairing again after a battery change. The pairing method is specific to the brand, so check the manual or the manufacturer's support page for your model.
Step 6: Unplug everything else and try once more
Switch off at the power point and disconnect all HDMI cables, USB drives, the antenna lead and any soundbar. Then power the TV up on its own.
Occasionally a faulty connected device or a damaged cable stops a TV from starting, and HDMI control features can also switch a TV off again the moment a connected box goes to sleep. If the TV starts with nothing attached, reconnect devices one at a time to find the culprit.
Step 7: Read the blink pattern, then stop
A standby light that blinks in a repeating pattern, for example a set number of flashes, a pause, then the same again, means the TV has detected a fault and shut itself down for protection. On some brands the number of blinks identifies the area of the fault, such as the power supply, the backlight or the main board.
The meaning of each count is specific to the brand and often to the model, so look it up on the manufacturer's support page rather than relying on a general chart. If the pattern returns after a full power cycle with everything disconnected, the fault is inside the set and the DIY checks are finished.
Careful: Do not keep switching a TV on and off to see if it will catch. Repeated start attempts on a faulty power supply or backlight can turn a modest repair into a larger one.
When to stop and call a repairer
- There is no standby light at all with a proven power point and a sound mains lead.
- The standby light blinks in a repeating pattern that returns after a full power cycle.
- The TV clicks on and off repeatedly, or starts and shuts down again within a few seconds.
- The fault began straight after a storm, blackout or power surge.
- There is a burning smell, a buzzing or squealing noise from the back of the set, or visible scorching.
- The TV trips the safety switch or a circuit breaker when it is plugged in.
Power supply boards in televisions and amplifiers store a dangerous charge even after the plug is pulled. Internal work belongs with a technician. Everything in our guides can be done from the outside.
What it costs
- Doing it yourself
- Usually $0. Remote batteries, a replacement mains lead or a new power board are each a small purchase.
- Professional repair
- Call-out or assessment fees of $80–$200 are common. The repair itself varies widely by brand, model and which board has failed, so ask for a quote after diagnosis.
Reliable Melbourne price data for TV repair is thin, so treat any figure quoted before the set has been inspected as a guess. Ask whether the assessment fee is credited against the repair. See our Melbourne repair cost guide for more.
Repair or replace?
A failed power supply board is one of the more repairable TV faults. The board is a separate part, and replacing or repairing it is usually far cheaper than anything involving the screen itself. On a mid-range or premium TV in otherwise good condition it is generally worth getting a quote.
The sums change for small or budget sets. An assessment fee plus a part can approach the price of a new entry-level TV, so compare the quote with what an equivalent replacement costs before you agree to the work.
Check your rights before paying anyone. Under the Australian Consumer Law a TV must last a reasonable time, which can be longer than the manufacturer's warranty, and the remedy comes from the retailer that sold it. A TV that dies after two or three years of normal use is worth raising with the seller first. If you do replace it, the old set is e-waste and cannot go to landfill in Victoria. Council transfer stations and drop-off points under the national TV and computer recycling scheme accept TVs.
Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.
Common questions
Why is the standby light on but the TV will not turn on?
The TV has power but is not responding to the command. The most common causes are a flat or unpaired remote and a software lock-up. Try the power button on the TV itself, then unplug the set for a full minute and try again. If the light stays steady and nothing responds after that, the main board may be at fault.
What does a blinking red light on my TV mean?
It is a fault indication. The TV has detected a problem, commonly in the power supply, backlight or main board, and has shut down to protect itself. On some brands the number of blinks narrows down the fault. Check the manufacturer's support page for your model, and note the count for the repairer.
Can a power surge kill a TV?
Yes. Surges from storms and from power being restored after a blackout are a common cause of power supply failure. A surge-protected power board reduces the risk but does not eliminate it, and the protection inside those boards wears out over time. If the damage followed a storm, your home contents insurance may cover it, so check your policy.
Is it safe to open the TV to look for a blown fuse or bulging capacitors?
No. The power supply board stores enough charge to give a serious shock even with the TV unplugged. A blown internal fuse has also usually blown for a reason, so replacing it alone rarely fixes the fault. Leave internal inspection to a repairer.
My TV turns itself off after a few seconds. Is that the same fault?
It is closely related. A TV that starts and then shuts down is usually protecting itself from a fault in the backlight or power supply. Check that a sleep timer or power-saving setting is not responsible, disconnect all external devices, and if it still happens, have it assessed.
Melbourne repairers for tvs & audio
Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.
European Electronics
Shopfront & mobileShop 7, 265 Wickham Rd, Moorabbin VIC 3189
Repairs TVs, amplifiers, turntables, home theatre and audio equipment and Sony cameras, in its workshop or in-home, for brands including Sony, Samsung, LG, Hisense, Bang & Olufsen, Yamaha, Panasonic and Pioneer.
Authorised Sony service agent that also repairs other brands.
Service Scene Electronic Servicing
Shopfront & mobile61 Wadham Pde, Mount Waverley VIC 3149
Repairs LCD, LED, OLED and plasma TVs and monitors, audio equipment, projectors, microwaves and vacuum cleaners, by walk-in or call-out.
Authorised LG service agent that also repairs other brands.
Optimum Electronic Solutions
Shopfront & mobile31 Prime St, Thomastown VIC 3074
Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.
JLS Electronics Service Centre
ShopfrontUnit 12, 173-181 Rooks Rd, Vermont VIC 3133
Service centre for hi-fi and home theatre equipment including amplifiers, valve preamplifiers, turntables and pro DJ gear, from brands such as Denon, NAD, Yamaha, Pioneer, Naim, Onkyo, Arcam and Cambridge Audio.
This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.
More tvs & audio guides
TV has sound but no picture: the torch test and other checks
Black screen but the sound still works? Use the torch test to spot a failed backlight, rule out inputs and settings, and see what is worth repairing.
HDMI no signal on your TV: how to get the picture back
TV showing no signal from a set-top box, console, streaming stick or soundbar? Work through inputs, cables, ports, CEC and ARC quirks and resolution.