Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

TV has sound but no picture: the torch test and other checks

Easy15–30 minutesReviewed By the MelbourneFix team

The short answer

If you can hear the TV but the screen is black, shine a torch at the screen in a dark room. A faint picture means the backlight has failed, which is usually repairable. No image at all, with the inputs and settings ruled out, points to the panel or its driver boards.

Sound without a picture tells you a lot. The power supply is working, the main board is running and the TV is receiving a signal. What is missing is either the image itself or the light behind it.

Most TVs sold in Australia are LCD sets, including those marketed as LED, QLED and Mini LED. They form the image on a liquid crystal layer and light it from behind with strips of LEDs. When those LEDs or the circuit driving them fail, the picture is still there but far too dark to see. OLED TVs are different. Each pixel makes its own light, so there is no backlight to fail.

Before assuming a hardware fault, it is worth ten minutes to rule out the simple causes: a setting that turns the screen off, the wrong input, or a connected device that is sending sound but no usable video.

Likely causes, most common first

  • Screen-off or picture-off setting

    DIY

    Sound is normal and the screen is completely black. The picture returns when a button on the remote is pressed, or after the setting is changed.

  • Source or HDMI handshake problem

    DIY

    The TV's own menu and volume bar appear normally, but one input shows black while its sound plays.

  • Failed backlight LEDs or backlight driver

    Professional

    A faint image is visible under a torch. The picture may flash up for a second at switch-on and then go dark, or parts of the screen may have been dim for a while beforehand.

  • Failed T-con board or its ribbon cables

    Professional

    The screen glows faintly grey in a dark room, so the backlight is on, but there is no image and no menu. Sometimes the screen is white or shows scrambled colours.

  • Failed panel

    Professional

    Vertical or horizontal lines, a band or half of the screen dark, ink-like blotches or visible cracks. On an OLED TV, a fully black screen with sound.

Before you start

Safety first

  • Do not remove the back of the TV. The power supply board holds a dangerous charge even when the set is unplugged, and the backlight circuit runs at high voltage.
  • Do not press, tap or flex the screen to try to bring the picture back. Panels crack easily and a cracked panel cannot be economically repaired.
  • Switch off at the power point before unplugging the mains lead from the back of the set.
  • If the black screen arrived with a burning smell, a pop or a flash, unplug the TV and do not keep testing it.

What you will need

  • Bright torch, or the torch on your mobile
  • A second HDMI cable known to work
  • The TV remote

Step-by-step checks

  1. Step 1: Bring up the TV's own menu

    Press the menu, home or settings button on the remote, then press volume up. If the menu or volume bar appears on screen, the panel and backlight are working and the problem lies with the input or the device connected to it.

    If you hear the menu's click sounds or the volume changes but nothing appears on screen at all, the TV is running without a visible picture. Keep going through the steps, but the torch test in step four is the one that matters most.

  2. Step 2: Check for a screen-off or power-saving setting

    Many TVs have a feature that switches the screen off while leaving the sound on, intended for listening to music or radio. It goes by names such as Screen Off or Picture Off and is usually found under the energy saving, power or sound settings. Pressing any button other than volume normally brings the picture back.

    If you can see the menu, also check that the backlight or brightness setting has not been turned right down, and that an energy saving mode is not set to its strongest level. A picture reset in the settings menu returns everything to the defaults.

  3. Step 3: Change inputs and test another source

    Use the input or source button to step through the inputs. Switch to the built-in tuner or open one of the TV's own apps. If free-to-air or an app shows a picture, the TV is fine and the fault is with the external device or its cable.

    For a device that gives sound but a black screen, unplug its HDMI cable at both ends and refit it firmly, then try another HDMI port on the TV and a different cable. Restart the device itself by unplugging its power for a minute.

    Sound with a black picture from a set-top box, console or streaming stick is often a failed HDMI handshake, where the two devices have not agreed on a video format or on copy protection. Powering both off at the wall, then starting the TV first and the device second, forces them to negotiate again.

  4. Step 4: Do the torch test

    Turn the TV on with something playing, darken the room and hold a bright torch a few centimetres from the screen, angled slightly. Move it slowly around and look closely at the lit patch.

    If you can make out a faint, shadowy image, such as menu text, a logo or people moving, the panel is producing a picture and the backlight is not lighting it. That is a backlight failure. If you see nothing in the torchlight but your own reflection, the fault is more likely the panel, the T-con board that drives it, or the main board.

    This test only applies to LCD-based TVs. An OLED set has no backlight, so a black screen with sound on an OLED points to the panel or its power circuits.

    Tip: Use a menu screen or a paused image with large, bright shapes. A dark movie scene is nearly impossible to pick out by torch.

  5. Step 5: Look at the screen in a dark room without the torch

    With the TV on and the room dark, look at whether the screen is truly black or glows a faint, even grey. A grey glow means the backlight is on. Combined with no image and no menu, that points away from the backlight and towards the T-con board, its ribbon cables or the panel.

    Also watch the screen at the moment you turn the TV on. A logo or picture that flashes up for a second or two and then goes dark while the sound carries on is a classic sign of a backlight fault. The TV detects a problem with the LED strips and shuts the backlight down to protect itself.

  6. Step 6: Power cycle once, then stop

    Unplug the TV at the power point for a full minute, hold the TV's own power button for about 15 seconds while it is unplugged, then plug it back in and try again. This clears software faults that can leave the screen blank.

    If the picture is still missing, you have done what can safely be done from outside the set. Write down what you found, especially the result of the torch test and whether the picture flashes at start-up. That information lets a repairer give you a much more useful answer over the phone.

    Careful: If the backlight is failing, avoid running the TV for long periods while you wait. Remaining LEDs in a failing strip are under extra stress, and some sets will cycle on and off repeatedly.

When to stop and call a repairer

  • The torch test shows a faint image, which means the backlight or its driver circuit has failed.
  • The picture flashes on for a second at start-up and then goes dark while the sound continues.
  • The screen glows grey but shows no image and no menu on any input.
  • There are lines, bands, blotches or dark sections on the screen as well as, or before, the loss of picture.
  • The picture went out with a pop, a flash or a burning smell.

Power supply boards in televisions and amplifiers store a dangerous charge even after the plug is pulled. Internal work belongs with a technician. Everything in our guides can be done from the outside.

What it costs

Doing it yourself
$0 for the checks. A replacement HDMI cable is a small purchase if a cable turns out to be the fault.
Professional repair
Call-out or assessment fees of $80–$200 are common. Backlight and board repairs vary a lot by screen size and model, so get a quote after diagnosis. A replacement panel usually costs close to the price of a new TV.

There is little reliable published pricing for TV repair in Melbourne. Ask whether the assessment fee is credited against the repair, and whether the quote covers all the LED strips or only the failed one. See our Melbourne repair cost guide for more.

Repair or replace?

The torch test result largely decides this. A backlight failure means the expensive part, the panel, is still good. The LED strips and the board that drives them are comparatively cheap parts, and the repair is usually far cheaper than a panel. The catch is labour and risk: reaching the strips means dismantling the screen assembly, and large, thin panels are easy to crack in the process. Some repairers decline very large sets for that reason, and many recommend replacing every strip at once, since the others are the same age.

A failed T-con board or main board is also generally repairable. A failed panel is not, in any practical sense. A replacement panel usually costs close to the price of a new TV, and panels for older models are often unavailable. Lines, bands and cracks almost always mean replacement.

Before paying for either, consider the age of the set. Under the Australian Consumer Law a TV must last a reasonable time, which can be longer than the manufacturer's warranty. A panel or backlight that fails after two or three years of ordinary use is a classic case to raise with the retailer you bought it from, and a major failure entitles you to choose a refund or a replacement. Take your receipt or bank statement and a clear description of the fault.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

What is the torch test and does it work on every TV?

It is a way to tell whether the screen is making a picture that simply is not being lit. You shine a torch closely at the screen in a dark room and look for a faint image. It works on LCD-based sets, including those sold as LED, QLED and Mini LED. It does not apply to OLED TVs, which have no backlight.

Can I replace the backlight strips myself?

We do not recommend it. The job means removing the back of the TV, where the power supply holds a dangerous charge, and then separating the fragile panel and diffuser sheets from the frame to reach the strips. Cracking the panel during this step is common even for experienced people, and it turns a repairable TV into scrap.

Why does the picture appear for a second and then disappear?

The TV checks its backlight at start-up. If one LED in a strip has failed, the driver circuit sees the wrong voltage or current and shuts the backlight off to protect itself, usually within a second or two. Sound carries on because the rest of the TV is working normally.

Does turning the backlight setting down make the LEDs last longer?

Running the backlight at full brightness all the time does shorten LED life, and many backlight failures happen on sets left on a vivid or shop-style picture mode. Using a standard or cinema mode with a moderate backlight level is easier on the LEDs and usually gives a more accurate picture as well.

Only one HDMI input is black. Is the TV faulty?

Probably not. If the TV's menu, apps and other inputs show a picture, the problem is with that device, its cable or that one port. Swap the cable, try the device in a different port and restart it. Our guide to HDMI no signal problems covers this in more detail.

Melbourne repairers for tvs & audio

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

European Electronics

Shopfront & mobile

Shop 7, 265 Wickham Rd, Moorabbin VIC 3189

Repairs TVs, amplifiers, turntables, home theatre and audio equipment and Sony cameras, in its workshop or in-home, for brands including Sony, Samsung, LG, Hisense, Bang & Olufsen, Yamaha, Panasonic and Pioneer.

Authorised Sony service agent that also repairs other brands.

Service Scene Electronic Servicing

Shopfront & mobile

61 Wadham Pde, Mount Waverley VIC 3149

Repairs LCD, LED, OLED and plasma TVs and monitors, audio equipment, projectors, microwaves and vacuum cleaners, by walk-in or call-out.

Authorised LG service agent that also repairs other brands.

Optimum Electronic Solutions

Shopfront & mobile

31 Prime St, Thomastown VIC 3074

Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.

JLS Electronics Service Centre

Shopfront

Unit 12, 173-181 Rooks Rd, Vermont VIC 3133

Service centre for hi-fi and home theatre equipment including amplifiers, valve preamplifiers, turntables and pro DJ gear, from brands such as Denon, NAD, Yamaha, Pioneer, Naim, Onkyo, Arcam and Cambridge Audio.

See all tvs & audio repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More tvs & audio guides