Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

HDMI no signal on your TV: how to get the picture back

Easy15–30 minutesReviewed By the MelbourneFix team

The short answer

A no signal message nearly always comes down to the wrong input, a cable or port that is not making contact, a device that is asleep or underpowered, or the two devices failing to agree on a video format. A full power-down and restart in the right order fixes most of the rest.

When a TV says no signal, it is telling you that nothing usable is arriving on the input it is looking at. The TV itself is usually fine. The problem sits somewhere along the chain: the device, the cable, the port, or the brief electronic conversation the two ends have before any picture is shown.

That conversation is called the HDMI handshake. The source and the TV exchange what resolutions and formats they support and confirm copy protection. If it fails, for instance because a cable is marginal or a device woke up in the wrong order, you get a black screen or a no signal message even though everything is plugged in.

The steps below apply to set-top boxes, game consoles, streaming sticks, Blu-ray players and soundbars. They start with the obvious and work up to the settings that catch people out.

Likely causes, most common first

  • Wrong input selected, or the device is off or asleep

    DIY

    The TV shows no signal on one input but the device's power light is off, amber or in standby. Often follows someone else using the TV.

  • Loose, damaged or inadequate HDMI cable

    DIY

    Picture comes and goes when the cable is touched, shows sparkles or flickers, or works at a lower resolution but not at 4K.

  • Failed HDMI handshake

    DIY

    Everything is connected and powered but the screen stays black, typically after a blackout, a software update or switching devices on in a different order.

  • Resolution or format the TV or port cannot accept

    DIY

    The device shows its start-up logo and then the picture drops out, or the fault began after changing a video setting or moving the device to another TV.

  • Soundbar or receiver in the chain, or a CEC or ARC quirk

    DIY

    Devices plugged into the soundbar or receiver show nothing, but work when plugged directly into the TV. The TV may switch inputs on its own.

  • Damaged HDMI port on the TV or the device

    Professional

    One port never works with any cable or device, the plug feels loose, or bent pins are visible inside the socket.

Before you start

Safety first

  • Switch devices off before plugging and unplugging HDMI cables where practical, and never force a plug. HDMI ports are soldered directly to the circuit board and are easily damaged.
  • Do not remove the back of the TV or open a set-top box or console to inspect a port. Look from the outside with a torch.
  • Take care moving a wall-mounted or large TV to reach the sockets. Get help rather than leaning the screen against furniture.
  • Keep cables from being pulled tight or bent sharply at the plug. Sideways strain on the plug is what breaks ports.

What you will need

  • A spare HDMI cable known to work
  • Torch
  • The remotes for the TV and the connected device

Step-by-step checks

  1. Step 1: Confirm the input and that the device is awake

    Look at the back or side of the TV and note which numbered HDMI port the device is plugged into. Then use the input or source button on the TV remote to select that same number. Do not rely on the label the TV has given the input, because names can be assigned to the wrong port.

    Check the device has power and is on rather than in standby. Press a button on its own remote to wake it. A set-top box or console in standby sends no picture, and the TV will report no signal even though the cable is fine.

  2. Step 2: Reseat the cable at both ends

    Unplug the HDMI cable from the TV and from the device, look into each plug and socket with a torch for dust or bent contacts, and push each end back in firmly until it seats. HDMI plugs have no latch and work loose when a cabinet is moved or a wall-mounted TV is swung out.

    If the plug feels sloppy in the socket, or the picture cuts in and out as you move the cable, either the cable or the port is damaged. The next step tells you which.

  3. Step 3: Swap ports, then swap the cable

    Move the device to a different HDMI port on the TV and select that input. If it works there, the original port may be faulty or set up differently. Then try a different HDMI cable, ideally one you know works on another device.

    Finally, if you can, plug a different device into the original port and cable. Changing one thing at a time is the quickest way to find out whether the device, the cable or the TV is at fault.

    For 4K at 60 frames a second with HDR, use a cable certified as Premium High Speed. For 4K at 120 frames a second from a current console, use one certified as Ultra High Speed, such as the cable supplied with the console. Older or very long cables may carry a 1080p picture perfectly and fail completely at 4K.

    Tip: Long passive cables are a common hidden cause. If the run is more than about five metres, test with a short cable before blaming anything else.

  4. Step 4: Power everything down and restart in order

    Switch off the TV, the device and any soundbar or receiver, then turn them all off at the power point and leave them for a full minute. Standby is not enough. The HDMI circuits stay powered in standby and can hold on to a failed handshake.

    Switch the TV on first and select the correct input. Next, turn on the soundbar or receiver if you have one and let it finish starting. Turn on the source device last. Each device then announces itself to one that is already listening.

  5. Step 5: Check streaming stick power

    Streaming sticks and small media players are often powered from a USB port on the TV. Many TV USB ports do not supply enough current, and they switch off when the TV does, so the stick restarts every time and can fail to start at all.

    Plug the stick into its supplied power adaptor and a power point instead. If the stick sits tight against other cables or the wall, use the short HDMI extender that many sticks come with so it is not under strain.

  6. Step 6: Rule out a resolution or format mismatch

    If the device shows its start-up logo and then the screen goes blank, it is likely sending a format the TV, the port or the cable cannot handle. This is common after a console or 4K box has been moved from another TV.

    On the TV, look for a per-input HDMI setting that enables the full 4K HDR signal. Manufacturers use names such as Enhanced format, Input Signal Plus or HDMI Deep Colour. On some TVs only certain ports support the higher modes, and they are usually labelled. Try turning the setting on for a 4K device, or off if the picture has just stopped working.

    On the device, lower the output resolution to 1080p if you can reach its menu on another TV or port. Consoles have a low-resolution start-up mode for exactly this situation, covered in our guide to a console with no picture.

  7. Step 7: Simplify the soundbar or receiver chain

    If your devices plug into a soundbar or receiver that then feeds the TV, connect one device directly to the TV as a test. If the picture returns, the soundbar is the weak link. Some older soundbars cannot pass through 4K HDR or newer formats, and many pass nothing while switched off unless a standby pass-through setting is turned on.

    For a soundbar that takes audio from the TV, the cable must go into the TV port marked ARC or eARC, and HDMI control must be enabled on both the TV and the soundbar. HDMI control is the feature called CEC, sold under names such as Anynet+, Simplink and Bravia Sync. ARC generally will not work with it switched off.

    CEC also lets devices turn each other on and change inputs, which is the usual reason a TV jumps to another input by itself. If that is the behaviour you are seeing, turn HDMI control off on the offending device rather than on the TV.

When to stop and call a repairer

  • One HDMI port on the TV does not work with any cable or device, and you need that port.
  • No HDMI port on the TV works, but the built-in tuner and apps show a picture normally.
  • You can see bent or missing pins in a socket, or the socket moves or has been pushed back into the case.
  • The device gives no signal on any TV with any cable, which means the fault is in the device's HDMI output.
  • The fault started after a storm or power surge. HDMI ports are a common casualty because surges travel along connected cables.

Power supply boards in televisions and amplifiers store a dangerous charge even after the plug is pulled. Internal work belongs with a technician. Everything in our guides can be done from the outside.

What it costs

Doing it yourself
$0 for most fixes. A certified HDMI cable is typically $10–$40 depending on length and rating.
Professional repair
Call-out or assessment fees of $80–$200 are common. HDMI port and board repairs vary by model, so ask for a quote after diagnosis.

There is little reliable published pricing for this work in Melbourne. Ask whether the assessment fee is credited against the repair, and compare the quote with the value of the TV or device. See our Melbourne repair cost guide for more.

Repair or replace?

Most no signal faults cost nothing or the price of a cable. Expensive cables are not better at carrying a digital signal than certified inexpensive ones. What matters is the certification level and that the cable is no longer than it needs to be.

If one HDMI port on a TV has failed and the others work, the cheapest answer is to use another port. If you have run out of ports, an HDMI switch box, or a soundbar or receiver with several inputs, gives you more without repairing anything.

When every HDMI port on a TV is dead, the fault is on the main board. That is repairable on many sets, by replacing the board or the damaged ports, and is usually far cheaper than a panel fault. On a small or older TV, weigh the quote against the price of a replacement. If the TV is only a few years old, raise it with the retailer first, as the Australian Consumer Law requires products to last a reasonable time regardless of the warranty period.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Why does my TV say no signal when everything is plugged in?

Because being plugged in is not the same as sending a picture. The device may be in standby, the TV may be on a different input, the cable may not be fully seated, or the handshake between the two may have failed. Powering everything off at the wall for a minute and restarting TV first, source last, resolves a large share of these.

The TV says no signal on free-to-air channels. Is that an HDMI problem?

No. That message on the TV's own tuner means it is not receiving a broadcast signal from the antenna. Check the antenna lead at the back of the TV and at the wall plate, then try a channel rescan. If several TVs in the house are affected, the antenna or its cabling needs attention.

Do I need a new HDMI cable for a 4K TV?

Not necessarily. Many existing High Speed cables carry 4K at lower frame rates without trouble. If you get dropouts, sparkles or no picture at 4K but a stable picture at 1080p, replace the cable with one certified Premium High Speed, or Ultra High Speed for 4K at 120 frames a second.

What is the difference between ARC and eARC?

Both send sound from the TV back down the HDMI cable to a soundbar or receiver, so one cable does the job. ARC carries stereo and compressed surround sound. eARC has much more capacity and can carry uncompressed and higher-quality formats. Both ends need to support eARC to use it, otherwise the connection falls back to ARC.

Why does my TV keep switching inputs by itself?

That is HDMI control, also called CEC. A connected device has woken up, perhaps for an update, and told the TV to switch to it. You can turn the feature off in the settings of the device that keeps taking over. Turning it off on the TV works too, but you may lose soundbar volume control and ARC.

Melbourne repairers for tvs & audio

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

European Electronics

Shopfront & mobile

Shop 7, 265 Wickham Rd, Moorabbin VIC 3189

Repairs TVs, amplifiers, turntables, home theatre and audio equipment and Sony cameras, in its workshop or in-home, for brands including Sony, Samsung, LG, Hisense, Bang & Olufsen, Yamaha, Panasonic and Pioneer.

Authorised Sony service agent that also repairs other brands.

Service Scene Electronic Servicing

Shopfront & mobile

61 Wadham Pde, Mount Waverley VIC 3149

Repairs LCD, LED, OLED and plasma TVs and monitors, audio equipment, projectors, microwaves and vacuum cleaners, by walk-in or call-out.

Authorised LG service agent that also repairs other brands.

Optimum Electronic Solutions

Shopfront & mobile

31 Prime St, Thomastown VIC 3074

Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.

JLS Electronics Service Centre

Shopfront

Unit 12, 173-181 Rooks Rd, Vermont VIC 3133

Service centre for hi-fi and home theatre equipment including amplifiers, valve preamplifiers, turntables and pro DJ gear, from brands such as Denon, NAD, Yamaha, Pioneer, Naim, Onkyo, Arcam and Cambridge Audio.

See all tvs & audio repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More tvs & audio guides