Split system not cooling (or heating) properly: checks you can do yourself
The short answer
A split system does not make cold. It moves heat. The indoor unit absorbs heat from the room air as it passes over a cold coil, the refrigerant carries that heat outside, and the outdoor unit dumps it into the outside air. In winter a reverse cycle unit runs the same process backwards. Anything that stops air moving freely across either coil, inside or out, cuts the performance sharply.
That is why the first checks are about airflow and settings, not parts. Filters clogged with dust are the most common reason for a unit that runs all day without cooling the room. A remote left in the wrong mode is a close second, especially at the change of season.
The steps below apply to wall-mounted split systems in both cooling and heating. They also explain the winter defrost cycle, which looks like a breakdown and is not one.
Likely causes, most common first
Wrong mode or settings on the remote
DIYAir comes out but is not cold. The remote shows fan, dry, heat or auto, or the set temperature is higher than the room.
Dirty filters
DIYWeak airflow from the indoor unit, a musty smell, and a room that never quite gets comfortable. Filters have not been washed this season.
Outdoor unit blocked or coil dirty
DIYPerformance falls away on hot afternoons. Leaves, lint, pet hair or cobwebs coat the back of the outdoor unit, or it is boxed in by plants or stored items.
Iced-up indoor coil
DIY or professionalAirflow drops to almost nothing, ice or frost is visible behind the filters, and water drips when the unit is turned off.
Low refrigerant from a leak
ProfessionalAir is only slightly cool although the outdoor unit runs constantly. Frost on the thin copper pipe at the outdoor unit, oily marks at pipe joints, or a hissing or bubbling sound.
Electrical or component fault
ProfessionalBreaker trips, outdoor fan or compressor does not start, or a light on the indoor unit flashes a fault code.
Before you start
Safety first
- Turn the unit off with the remote, then switch off the isolator beside the outdoor unit, or the circuit breaker, before cleaning the outdoor unit or reaching into the indoor unit beyond the filters.
- Do not remove any cover that needs a screwdriver, apart from what the manual describes for filter access. Split systems are hardwired, and electrical work on them is for a licensed electrician or suitably licensed technician.
- Never try to top up, release or test refrigerant yourself. Anyone working on the refrigerant circuit must hold a refrigerant handling licence from the Australian Refrigeration Council.
- Use a stable step ladder to reach the indoor unit, not a chair, and do not lean on the unit or pull on its front panel for balance.
- The aluminium fins on both coils are thin and sharp. Do not press on them, and do not use a pressure washer on the outdoor unit.
What you will need
- Step ladder
- Vacuum cleaner with a soft brush attachment
- Mild dishwashing detergent and lukewarm water
- Garden hose with a gentle spray setting
- Fresh batteries for the remote
- Torch
- Household thermometer (optional)
Step-by-step checks
Step 1: Check the remote and the mode
Look at the remote's display. For cooling it should show cool mode, usually a snowflake symbol. The sun symbol is heating, the water droplet is dry mode and the fan symbol circulates air without cooling it. Auto mode lets the unit choose for itself and often chooses badly in mild weather, so select cool or heat directly.
Set the temperature to something sensible. Around 24 to 26 degrees for cooling and 18 to 20 for heating keeps running costs down, and the unit must be set lower than the room in cooling, or higher in heating, before it does anything. Setting it to 16 does not cool the room any faster.
If the display is faint or the unit does not beep when you press a button, replace the remote's batteries. Check that a timer or sleep setting has not been switched on by accident.
Tip: After any change of mode, or after the power has been off, wait about three minutes. The unit deliberately delays restarting the compressor to protect it.
Step 2: Remove and wash the filters
Turn the unit off. Lift the front panel of the indoor unit from the bottom edge or the side tabs until it clicks open. The filters are the mesh screens across the front. Lift each one slightly and slide it down and out.
Take them outside and vacuum the dust off with a brush attachment, or wash them in lukewarm water with a little dishwashing detergent. Rinse from the clean side so the dust is pushed back out the way it came in.
Shake off the water and let the filters dry fully in the shade. Do not use hot water, a hair dryer or direct sun, because the plastic frames warp. Slide them back in, making sure they sit behind their tabs, and close the panel firmly.
Tip: In a house with pets or during heavy summer use, check the filters every few weeks. Otherwise once at the start of each season is the minimum.
Careful: Do not run the unit with the filters out. Dust goes straight onto the coil, which is far harder and more expensive to clean.
Step 3: Clear and clean the outdoor unit
The outdoor unit needs to pull air through the coil at the back and sides and blow it out the front. Move bins, pot plants and stored items away, trim back shrubs and grass, and follow the clearances in your installation manual. If the unit is enclosed by a screen or under a deck, make sure the hot air has somewhere to go.
Switch off the isolator next to the unit. Brush leaves, lint and cobwebs off the coil with a soft brush, working in the direction of the fins. Then rinse the coil with a garden hose on a gentle setting, aiming straight at the fins from the outside.
Let it drain for a few minutes, turn the isolator back on and restart the unit.
Careful: A pressure washer will flatten the fins and can force water into the electrics. If the coil is matted with grease or dirt that a hose will not shift, book a professional clean.
Step 4: Look for ice on the indoor coil
If airflow has dropped away, open the front panel and shine a torch on the metal coil behind the filters. Frost or solid ice means the coil has frozen over and air can no longer pass through it.
Turn the unit to fan-only mode, or turn it off, and let the ice melt completely. This can take a couple of hours. Put a towel down in case of drips. Wash the filters while you wait.
If the coil ices up again with clean filters and a normal temperature setting, the usual cause is low refrigerant, and that needs a technician.
Step 5: Check the breaker and the outdoor unit
If the indoor unit is completely dead, check the switchboard for a tripped air conditioner breaker and check that the isolator at the outdoor unit is on. Reset a tripped breaker once. If it trips again, leave it off and call a technician.
If the indoor unit runs but the air is not cold, go outside after five minutes in cool mode. The outdoor fan should be spinning and you should hear the lower hum of the compressor. In cooling, the air leaving the outdoor unit should feel distinctly warm.
A silent outdoor unit, a fan that spins without the compressor hum, or a buzzing or clicking noise from a unit that will not start are all faults for a technician.
Step 6: Run a simple performance test
With clean filters and a clear outdoor unit, close the doors and windows and run the unit in cool mode for 15 minutes. The air from the indoor unit should feel clearly cold on the back of your hand, not just cool.
If you have a household thermometer, compare the room air with the air leaving the louvres. A healthy unit in cooling typically delivers air several degrees colder than the room, commonly somewhere around 8 to 12 degrees colder. A difference of only two or three degrees, with the compressor running, suggests a refrigerant or compressor problem.
Keep expectations realistic on extreme days. Every air conditioner loses capacity as the outdoor temperature climbs, and a unit that was sized tightly for the room will struggle on a 40 degree afternoon without being faulty. Closing blinds on west-facing windows and starting the unit before the house heats up make a real difference.
Step 7: In winter, learn to recognise the defrost cycle
When a reverse cycle unit heats on a cold, damp Melbourne morning, frost forms on the outdoor coil. Every so often the unit pauses to melt it. The indoor fan stops or slows, warm air ceases for several minutes, a light on the indoor unit may blink, and the outdoor unit can hiss, gurgle and give off steam while water runs from underneath.
This is normal and the heating returns by itself, usually within about ten minutes. Do not turn the unit off and on during a defrost, because that only lengthens the wait.
It becomes a fault when the outdoor unit stays encased in ice for hours, when defrosts come back to back so the room never warms, or when the heating is weak in mild weather. Clean the filters and clear the outdoor unit first. If nothing changes, book a service.
When to stop and call a repairer
- The coil ices up again after you have thawed it and cleaned the filters.
- There is frost on the copper pipes at the outdoor unit, oily residue at the pipe connections, or a hissing sound.
- The outdoor unit does not start, or its fan runs without the compressor.
- The breaker or safety switch trips when the unit is turned on.
- A light on the indoor unit flashes a fault pattern, or the remote shows an error code that returns after the power has been off for a few minutes.
- The air is barely cooler than the room with clean filters, a clear outdoor unit and the right mode.
Energy Safe Victoria recommends that gas heaters are serviced at least every two years by a qualified gasfitter, including a carbon monoxide test. A carbon monoxide alarm is a back-up, not a substitute. Air conditioner refrigerant work requires an ARCtick refrigerant handling licence.
What it costs
- Doing it yourself
- $0 for cleaning filters and the outdoor unit. A pack of batteries for the remote.
- Professional repair
- About $200–$300 for a split-system service. A regas is typically $200–$400, or $400–$700 where leak detection and repair are included. Call-out or diagnostic fees of $80–$200 are common and are often credited against the repair.
Indicative ranges from 2026 Australian cost guides, not Melbourne quotes. Ask what the service includes and get a quote before agreeing to any refrigerant work. See our Melbourne repair cost guide for more.
Repair or replace?
A dirty system, a failed fan motor, a capacitor or a sensor is worth repairing on almost any unit that is otherwise in good order. A professional clean on a neglected unit often restores performance that the owner had written off.
Refrigerant is where care is needed. The circuit is sealed, so a system does not use up its gas. If it is low, it has leaked. Topping it up without finding and fixing the leak is poor practice: the gas escapes again, you pay twice, and refrigerant ends up in the atmosphere. Ask the technician, who must hold an Australian Refrigeration Council licence, where the leak is and what the repair involves before any gas goes in.
Replacement starts to make sense for a unit well past ten years old with a leaking indoor coil or a failed compressor, or one that runs on an older refrigerant that has become expensive. If a fairly new unit fails, go back to the seller or installer first. The Australian Consumer Law requires goods to last a reasonable time, which can be longer than the manufacturer's warranty.
Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.
Common questions
Does my air conditioner need regassing every few years?
No. The refrigerant circulates in a sealed circuit and is not consumed. A system that needs gas has a leak, and the leak should be found and repaired, by a technician with a refrigerant handling licence, before it is recharged.
Why does my split system stop blowing warm air for a few minutes in winter?
It is defrosting the outdoor coil. On cold, humid mornings frost builds up outside, and the unit briefly pauses heating to melt it. The indoor fan stops, a light may blink, and the heating resumes without you doing anything.
How often should I clean the filters?
At the start of summer and the start of winter at the very least, and every few weeks during heavy use or in a home with pets or a lot of dust. The manual for your model gives the manufacturer's interval.
What temperature should I set for cooling?
Around 24 to 26 degrees suits most households and keeps running costs reasonable. A much lower setting does not cool the room faster. It only makes the unit run longer.
Is it normal for water to drip from the outdoor unit?
Yes. In cooling, condensation from the indoor unit drains outside through a small pipe. In heating, the outdoor unit itself sheds water when it defrosts. Water dripping inside the house is a different matter and should be dealt with promptly.
Melbourne repairers for air conditioning & heating
Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.
RapidFix Solutions
Mobile service113 East St, Hadfield VIC 3046
On-site repairs of ducted gas and reverse-cycle heating, split system, ducted and evaporative cooling, domestic fridges and freezers, washing machines, dryers, dishwashers, ovens and cooktops.
Services Glenroy, Coburg, Brunswick, Pascoe Vale, Essendon and other suburbs.
Dynamic Heating and Cooling
Mobile serviceMobile · West
Services and repairs split system and ducted air conditioning and gas ducted heating, including carbon monoxide testing, for brands including Daikin, Mitsubishi, Fujitsu, ActronAir, Panasonic, Braemar, Brivis and Vulcan.
Services inner and north-western suburbs such as Abbotsford, Brunswick, Footscray, Sunshine and Williamstown.
Advance Heating and Cooling
Shopfront & mobileShop 3, 296 Ballarat Rd, Braybrook VIC 3019
Services and repairs gas, reverse-cycle and electric ducted heating, split systems, evaporative cooling and gas wall furnaces, naming Brivis, Braemar, Bonaire and Rinnai.
Plum Trade Services
Mobile serviceUnit 4, 22-30 Wallace Ave, Point Cook VIC
Repairs and services split system, multi-split, ducted reverse-cycle and evaporative air conditioning and ducted gas heating, for brands including Brivis, Braemar, Bonaire, Vulcan, Daikin, Fujitsu, Mitsubishi and Panasonic.
Services the western suburbs.
This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.
More heating & cooling guides
Air conditioner leaking water inside: how to find the cause and stop the drip
Water dripping from your split system's indoor unit? Check the filters, the drain outlet outside and for ice on the coil before you book a technician.
Ducted gas heater not working: safe checks, and when to call a gasfitter
Ducted heating not starting or blowing cold air? Check the thermostat, power, return-air filter and vents, and know the carbon monoxide warning signs.