Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Ducted gas heater not working: safe checks, and when to call a gasfitter

Easy20–40 minutesReviewed By the MelbourneFix team

The short answer

Check the thermostat batteries and settings, the power supply, the return-air filter and the vents. If the heater still will not light, locks out again after a reset, or anyone in the house feels unwell while it is running, turn it off and call a licensed gasfitter.

Ducted gas heating is the standard way a great many Melbourne houses keep warm, and it tends to fail on the first properly cold night of the year, after sitting idle since spring. The heater itself lives out of sight in the roof space, under the floor or in a cabinet outside. What you deal with day to day is the thermostat on the wall, the return-air grille and the vents.

Fortunately that is also where many of the faults are. Flat thermostat batteries, a schedule that has been changed, a tripped breaker or a return-air filter matted with dust will each stop a perfectly healthy heater.

The burner, the ignition and the gas train are a different matter. A ducted gas heater is a Type A gas appliance, and anything involving those parts is licensed gasfitter work. Because a faulty gas heater can produce carbon monoxide, read the safety section before you start.

Likely causes, most common first

  • Thermostat batteries flat, or settings changed

    DIY

    Thermostat screen is blank or faint, or shows a low battery symbol. The heater does not respond at all, or the controller is on a timer, in off mode or in fan-only mode.

  • No power to the heater

    DIY

    Nothing happens when heat is called for. No click, no fan. Often follows a power cut or a tripped safety switch.

  • Blocked return-air filter or grille

    DIY

    Heater starts, runs for a few minutes, shuts down and tries again. Airflow from the vents is weak and the system is noisier than usual.

  • Too many vents or zones closed

    DIY

    Heater cycles on and off, or some rooms get nothing. Furniture or rugs cover vents, or most zones are switched off.

  • Ignition, pilot or flame sensor fault

    Professional

    The fan runs but the air is cold, you hear repeated clicking with no burner, or the controller shows a fault code and locks out.

  • Fan motor, control board or gas valve failure

    Professional

    Burner lights but no air comes from any vent, or the heater is completely dead with power and a working thermostat.

Before you start

Safety first

  • Carbon monoxide has no smell, colour or taste. Early symptoms resemble the flu without a fever: headache, dizziness, nausea, tiredness, shortness of breath and confusion. A strong clue is that people feel worse while the heater is on and better when they leave the house, or that several people or pets are affected together.
  • If you suspect carbon monoxide, turn the heater off, open doors and windows, get everyone outside into fresh air and seek medical advice. Call 000 if anyone is seriously unwell. Do not use the heater again until a licensed gasfitter has tested it.
  • Energy Safe Victoria recommends that gas heaters are serviced at least every two years by a qualified gasfitter, and that the service includes a carbon monoxide test. A carbon monoxide alarm is a back-up only. It is not a substitute for servicing.
  • If you smell gas: turn the heater off, do not operate switches or light a flame, open up the house, turn the gas off at the meter if it is safe to do so, then go outside and call your gas distributor's emergency line, which is printed on your gas bill, or 000.
  • Do not remove the heater's covers, and do not attempt work on the burner, pilot, gas valve or flue. Gas heaters must be serviced and repaired by a licensed gasfitter. Gasfitters in Victoria are licensed by the Building and Plumbing Commission, and Energy Safe Victoria is the gas safety regulator.
  • Stay out of the roof space and from under the floor. Both are hazardous places to move around, and nothing in there is a household job on a ducted heater.

What you will need

  • Fresh batteries for the thermostat (check the type in the battery compartment)
  • The user manual for the heater and for the thermostat or controller
  • Vacuum cleaner with a brush attachment
  • Torch
  • Screwdriver or coin, if the return-air grille has fasteners
  • Pen and paper to note any fault code

Step-by-step checks

  1. Step 1: Check the thermostat or controller

    A blank or faded display usually means flat batteries. Many wall thermostats run on batteries that sit behind the front cover or in a slide-out tray. Replace them all with fresh ones of the same type. Some networked and touch-screen controllers are powered from the heater instead, and a blank screen on one of those points to a power problem at the heater.

    Next, check the settings. The controller must be on and in heat mode, not off or fan-only, and the set temperature must be a few degrees above the current room temperature. Turn it up to 22 and wait a couple of minutes.

    Look at the clock and the program. If the time is wrong after a power cut or a battery change, a programmed schedule can keep the heater off when you expect it on. Switch to manual mode to test.

    Tip: If the display shows a fault code or a flashing symbol, write it down before you do anything else. The manual lists what each code means, and a gasfitter will ask for it.

  2. Step 2: Check the power supply

    The heater needs electricity for its controls, igniter and fan even though it burns gas. Go to the switchboard and look for a tripped circuit breaker or safety switch. Reset it once.

    Some heaters have an isolating switch, or plug into a power point, close to the unit. If your heater sits outside at ground level and the switch is in plain view, check that it is on. Do not climb into the roof space or crawl under the floor to look for one.

    If the breaker or safety switch trips again when the heater tries to start, leave it off and call a technician.

  3. Step 3: Clean the return-air grille and filter

    The return-air grille is the large grille, usually in a hallway wall, ceiling or floor, where the system draws air back in. Many systems have a filter directly behind it. Open the grille using its clips or fasteners and slide the filter out.

    Vacuum both sides of the filter. If the manual says it is washable, rinse it and let it dry fully before refitting. Vacuum the grille itself and make sure nothing is leaning against it or covering it.

    A choked return starves the heater of air. The heat exchanger then gets too hot, a safety limit switch shuts the burner down, and the heater starts again once it has cooled. That stop-start pattern is the classic sign, and cleaning the filter often cures it.

    Careful: Not every system has a filter at the grille, and some have none that the householder can reach. If you cannot find one, check the manual and do not go looking for it at the heater.

  4. Step 4: Open the vents and check the zones

    Walk through the house and make sure the floor or ceiling vents are open and not buried under rugs, furniture or curtains. A ducted heater is designed to push air through a minimum number of outlets, and closing most of them can make it overheat and cut out in the same way a blocked filter does.

    If the system is zoned, check on the controller that the zones you want are switched on. The manual will say whether one zone must always stay open.

    A single room with weak or no airflow while the rest of the house is warm usually means a duct has come off, been crushed or split. Ducts live in the roof space or under the floor, so that is a repair for a heating technician.

  5. Step 5: Check the gas supply

    See whether your other gas appliances work, such as the cooktop or the hot water. If nothing works, check that the valve at the gas meter is open, with the handle in line with the pipe, and contact your gas retailer if you cannot see a reason for the supply being off.

    If the other appliances work and the heater does not light, the fault is in the heater.

  6. Step 6: Reset once, only as the manual describes

    Many ducted heaters go into a lockout after several failed attempts to light, and they show this as a fault code or a flashing light on the controller. The user manual explains the reset for your model. It is often a reset button on the controller, or switching the heater off at the thermostat for a set time.

    Follow the manual's method and do it once. If the heater starts and runs normally, the lockout may have been caused by a brief interruption to the gas or power.

    Some older heaters have a pilot light that burns continuously. If the manual and the label on the heater give relighting instructions, and the heater can be reached safely from outside, you may follow them to the letter. A pilot that will not light, or will not stay lit, is a gasfitter's job.

    Careful: A heater that locks out again after a reset is refusing to run for a safety reason. Do not keep resetting it. Repeated attempts can let unburnt gas build up.

When to stop and call a repairer

  • Anyone in the house has headaches, dizziness or nausea while the heater is running. Turn it off, ventilate and get medical advice before anything else.
  • You smell gas, or notice a burning, sooty or sharp smell from the vents that lasts beyond the first few minutes of the season's first run.
  • The heater locks out again after one reset, or the same fault code keeps returning.
  • The fan runs but the air stays cold, or you can hear repeated clicking without the burner lighting.
  • The breaker or safety switch trips when the heater starts.
  • The heater has not been serviced, with a carbon monoxide test, in the past two years.

Energy Safe Victoria recommends that gas heaters are serviced at least every two years by a qualified gasfitter, including a carbon monoxide test. A carbon monoxide alarm is a back-up, not a substitute. Air conditioner refrigerant work requires an ARCtick refrigerant handling licence.

What it costs

Doing it yourself
$0 for the checks, plus a set of thermostat batteries. A replacement return-air filter if yours is torn or cannot be cleaned.
Professional repair
A call-out or diagnostic fee of $80–$200 is common and is often credited against the repair. Repair costs for ducted gas heaters vary widely with the brand, the part and how hard the unit is to reach, so ask for a written quote after diagnosis.

Indicative call-out range from 2026 Australian cost guides, not Melbourne quotes. Ask whether a carbon monoxide test is included when you book a service or repair. See our Melbourne repair cost guide for more.

Repair or replace?

Igniters, flame sensors, fan motors and thermostats are routine repairs, and on a heater in good condition they are generally worth doing. Ask the gasfitter for the quote and for an honest view of the unit's overall condition while the covers are off.

The picture changes with age and with the heat exchanger. A cracked or corroded heat exchanger can let combustion gases into the air being blown through the house. It is a safety fault, it is expensive to fix, and on an old heater it usually means the end of the unit. Discontinued parts and repeated lockouts on a heater that has done many winters point the same way.

If you are facing replacement, compare a like-for-like gas unit with reverse cycle heating, which also gives you cooling. The Victorian Energy Upgrades program has offered discounts for replacing ducted gas heating with efficient reverse cycle systems, so check what is currently available. For a heater that has failed early in its life, speak to the seller or installer first, because the Australian Consumer Law expects appliances to last a reasonable time, which can be longer than the manufacturer's warranty.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Why is my ducted heater blowing cold air?

Either the controller is in fan-only mode, or the fan is running without the burner lit. Check the mode first. If it is set to heat and the air stays cold, the burner is not lighting or is shutting down on a safety limit. Clean the return-air filter, try one reset as the manual describes, then call a gasfitter.

How often should a ducted gas heater be serviced?

Energy Safe Victoria recommends at least every two years, by a qualified gasfitter, with a carbon monoxide test as part of the service. Follow the manufacturer's interval if it is shorter.

I rent. Who is responsible for servicing and fixing the heater?

Your rental provider. In Victoria, rental providers must arrange a gas safety check of gas appliances every two years by a licensed gasfitter. Report a heater fault to the agent or rental provider in writing, and do not attempt repairs yourself.

Do I still need servicing if I have a carbon monoxide alarm?

Yes. An alarm is a useful back-up, but it only tells you once carbon monoxide is already in the room, and alarms can fail or be badly placed. Regular servicing with a carbon monoxide test is what stops the problem developing.

Is a dusty or burning smell normal when I first turn the heating on?

A light dusty smell for the first few minutes of the season is common, because dust that settled on the heat exchanger and in the ducts over summer is burning off. It should clear quickly. A smell that persists, smells of gas or soot, or comes with headaches is a reason to turn the heater off and call a gasfitter.

Melbourne repairers for air conditioning & heating

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

RapidFix Solutions

Mobile service

113 East St, Hadfield VIC 3046

On-site repairs of ducted gas and reverse-cycle heating, split system, ducted and evaporative cooling, domestic fridges and freezers, washing machines, dryers, dishwashers, ovens and cooktops.

Services Glenroy, Coburg, Brunswick, Pascoe Vale, Essendon and other suburbs.

Dynamic Heating and Cooling

Mobile service

Mobile · West

Services and repairs split system and ducted air conditioning and gas ducted heating, including carbon monoxide testing, for brands including Daikin, Mitsubishi, Fujitsu, ActronAir, Panasonic, Braemar, Brivis and Vulcan.

Services inner and north-western suburbs such as Abbotsford, Brunswick, Footscray, Sunshine and Williamstown.

Advance Heating and Cooling

Shopfront & mobile

Shop 3, 296 Ballarat Rd, Braybrook VIC 3019

Services and repairs gas, reverse-cycle and electric ducted heating, split systems, evaporative cooling and gas wall furnaces, naming Brivis, Braemar, Bonaire and Rinnai.

Plum Trade Services

Mobile service

Unit 4, 22-30 Wallace Ave, Point Cook VIC

Repairs and services split system, multi-split, ducted reverse-cycle and evaporative air conditioning and ducted gas heating, for brands including Brivis, Braemar, Bonaire, Vulcan, Daikin, Fujitsu, Mitsubishi and Panasonic.

Services the western suburbs.

See all heating & cooling repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More heating & cooling guides