Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Oven cooking unevenly or losing heat: door seal, hinges and temperature checks

Moderate45–90 minutes including a temperature testReviewed By the MelbourneFix team

The short answer

Start with an oven thermometer and a close look at the door seal. A perished clip-in seal is a job most people can do themselves, while a failed element, fan or thermostat needs a licensed technician.

An oven that browns one side of a tray, takes an age to cook a roast or heats up the kitchen more than the food has usually lost control of where its heat goes. Sometimes the cause is a faulty part. Just as often it is a flattened door seal, a door that no longer closes square, or a habit such as lining the oven floor with foil.

The trouble with oven complaints is that they are easy to argue about. Recipes vary, and so do tins and shelf positions. An oven thermometer settles it. It tells you whether the oven is actually reaching and holding the temperature on the dial, which decides whether you are dealing with a heat leak, an airflow problem or a control fault.

This guide covers the inspection and the one repair that is properly a householder's job on most ovens, which is replacing a clip-in door seal. The parts behind the panels stay with a licensed repairer.

Likely causes, most common first

  • Worn, flattened or torn door seal

    DIY

    Heat or steam escaping around the door, knobs and nearby cabinetry getting hot, slow preheating. The seal looks shiny, hard, frayed or is hanging loose.

  • Shelf position, overcrowding or blocked airflow

    DIY

    Uneven results with large trays, two shelves in use, or foil on the oven floor. One tray in the middle of the oven cooks acceptably.

  • Door not closing square or hinges worn

    DIY or professional

    A visible gap at one top corner, the door drops as it opens or springs back slightly ajar. Often follows someone leaning on the open door.

  • Thermostat or temperature sensor reading wrongly

    Professional

    An oven thermometer shows the oven sitting well above or below the set temperature on every function.

  • Fan not turning (fan-forced ovens)

    Professional

    Food burns at the back and stays pale at the front. No fan noise, or a scraping or squealing sound.

  • One element failed in a multi-element oven

    Professional

    Tops brown and bases stay raw, or the reverse. Preheating takes much longer than it used to.

Before you start

Safety first

  • Inspect and replace the seal only when the oven is completely cold. Turn the oven off at its circuit breaker before you work around the door opening.
  • Oven doors are heavier than they look, and the hinges are spring-loaded and can snap shut on fingers. If you lift the door off for access, follow the manual exactly and engage the hinge locking clips first.
  • Do not remove the rear panel inside the oven, the elements or any cover with wiring behind it. A built-in oven is hardwired, and in Victoria that work belongs to a licensed electrician or an appliance technician holding a Restricted Electrical Worker's licence.
  • Do not use the oven with a cracked inner door glass. Heat can cause damaged glass to shatter.
  • Read the thermometer through the door glass, or use oven mitts. The thermometer itself will be as hot as the oven.

What you will need

  • Oven thermometer (a simple dial type that hangs or stands on the shelf)
  • Torch
  • Sheet of paper for the door-grip test
  • Soft cloth, warm water and dishwashing detergent
  • Replacement door seal matched to your oven's model number
  • Oven mitts

Step-by-step checks

  1. Step 1: Measure the real temperature

    Place an oven thermometer in the middle of the centre shelf where you can read it through the glass. Set the oven to 180 degrees Celsius on the function you normally use and let it preheat. Wait a further 15 to 20 minutes after the thermostat light goes out so the cavity settles.

    Take three or four readings about five minutes apart without opening the door. Every oven cycles above and below its setting as the element switches on and off, so a swing of 10 to 15 degrees either side is normal. What you are looking for is the average.

    If the average is close to 180, the thermostat is doing its job and the problem lies in how heat is distributed or escaping. If it is out by 25 degrees or more, note the figure. A consistent offset points to the thermostat or sensor, and a repairer can test and replace or recalibrate it.

    Tip: Fan-forced settings cook faster than conventional ones. Most recipes written for a conventional oven need the temperature dropped by about 20 degrees when you use the fan.

  2. Step 2: Rule out shelf position and airflow

    Bake a single tray on the centre shelf with clear space on every side. Trays that touch the walls or fill the whole shelf stop air circulating, and the food nearest the heat source will always colour first.

    Remove any foil or liner from the oven floor and from the shelves. Foil on the floor reflects heat back at the lower element, blocks the air path and can damage the enamel. Manufacturers warn against it for good reason.

    With the oven cold, check that the rear panel, where the fan sits, is not caked with grease and that its slots are clear. Wipe it with a cloth and detergent. If one tray in the centre now cooks evenly, the oven is fine and the earlier results were down to loading.

  3. Step 3: Inspect the door seal

    With the oven cold, open the door and follow the seal around the opening with a torch. It is the rope-like or tubular gasket on the oven's front frame, or on some models on the door itself. A healthy seal is soft and springs back when pressed. Look for sections that are flattened, hard and glossy, frayed, torn, or pulled out of their fixing holes.

    Many ovens have a seal on the top and two sides only, with a deliberate gap along the bottom to let air in. That is not a fault. Check your manual or a parts diagram before assuming a piece has gone missing.

    Then try the paper test. Close the door on a sheet of paper at several points along the sides and top and pull gently. You should feel a definite grip. Places where the paper slides out freely are where heat is escaping.

    If the seal is only greasy, clean it with a soft cloth, warm water and a little detergent. Do not use oven cleaner on it, because caustic sprays harden the rubber.

  4. Step 4: Replace a clip-in door seal

    Find the model number on the rating plate, which is usually on the frame just inside the door, and order the seal for that exact model. Seals differ in length, corner shape and clip positions, and a near enough match will not seal properly.

    Before you remove the old seal, take a photo of how it sits, particularly at the corners and where the ends finish. Most seals are held by a small metal hook or clip at each corner that pushes into a hole in the frame. Ease each one out by pulling the seal gently away at the corner. Wipe the channel clean.

    Fit the new seal by hooking the top corners in first, then working down each side, pressing the clips fully home. The seal should lie flat with no twists. Close the door and repeat the paper test. A new seal can make the door feel slightly firm to close for the first few uses.

    Careful: If the seal is fixed by screws behind a panel, is bonded in place, or cannot be removed without dismantling the door, stop there and leave it to a repairer.

  5. Step 5: Check the door alignment and hinges

    Stand back and look at the closed door. The gap between the door and the control panel above should be even from left to right, and the door should sit flush with the cabinets on either side.

    Open the door halfway and let go. It should stay roughly where you leave it and close firmly for the last few centimetres. A door that drops, feels loose on one side or bounces back open has a worn or bent hinge, which will leave a gap that no new seal can close.

    On most ovens the door lifts off for cleaning and can be reseated by following the manual. If it came off recently and now sits crooked, one hinge arm may not be fully home in its slot, and refitting it carefully can fix the problem. Hinges that are bent or worn need replacing, usually as a pair, and that is a repairer's job.

  6. Step 6: Watch the fan and elements while it runs

    Run the oven on a fan-forced setting and look through the glass with the light on. The fan at the back should spin steadily and quietly. Then switch to the grill and confirm the top element glows evenly along its length.

    A fan that is not turning explains burning at the back. An element with a dark, unlit section or a blister explains pale tops or raw bases. Both faults sit behind panels and wiring, so note what you have seen and pass it on when you book the repair.

When to stop and call a repairer

  • The thermometer shows the oven consistently 25 degrees or more away from the set temperature.
  • The fan is not turning, or is noisy, on a fan-forced setting.
  • An element has a blister, a split or a section that does not glow.
  • The door drops, will not stay closed or sits visibly crooked after you have reseated it.
  • The inner or outer door glass is cracked or loose.
  • The seal is not a clip-in type and cannot be changed without dismantling the door.

In Victoria, disconnecting or reconnecting a hardwired oven or cooktop must be done by a licensed electrician or a technician with a restricted electrical licence. Gas appliances must be repaired by a licensed gasfitter. You can check electrical licences with Energy Safe Victoria and gasfitters with the Building and Plumbing Commission.

What it costs

Doing it yourself
The price of an oven thermometer and a replacement seal. Seal prices depend heavily on brand and model, so check with a parts supplier using your model number.
Professional repair
$220–$480 for an oven element replaced and fitted. A call-out or diagnostic fee of $80–$200 is common and is often credited against the repair. Hinge, fan motor and thermostat repairs vary, so ask for a quote.

Indicative ranges from 2026 Australian cost guides, not Melbourne quotes. Give the repairer your model number and thermometer readings when you ring, because it helps them quote and bring the right parts. See our Melbourne repair cost guide for more.

Repair or replace?

Seals, hinges, elements and fan motors are all ordinary wear items, and replacing any one of them on a sound oven is money well spent. A new seal in particular is a small outlay that often restores an oven people had assumed was worn out.

Think harder when the faults stack up: a door that needs hinges and glass, a failing thermostat and an interior with chipped, rusting enamel. Parts availability matters too. For older or discontinued models, ask the repairer whether the parts can still be obtained before you pay for a diagnostic visit.

If an oven that is a few years old cannot hold its temperature, take it up with the retailer. Under the Australian Consumer Law, goods must last a reasonable time, and that period can be longer than the manufacturer's warranty.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

How do I know if my oven door seal needs replacing?

Look for flattened, hardened, frayed or torn sections, or a seal hanging out of its clips. Heat or steam escaping around the door, hot control knobs and a sheet of paper that slides freely out of the closed door are the practical signs.

Is it normal for there to be no seal along the bottom of the door?

On many ovens, yes. The gap is part of how the oven draws in air. Check the manual or a parts diagram for your model before deciding the seal is incomplete.

How accurate should an oven be?

Domestic ovens cycle either side of the set temperature, so swings of 10 to 15 degrees are expected. An average that stays within about 10 to 15 degrees of the dial is reasonable. A steady error of 25 degrees or more is worth having checked.

Why does my oven burn food at the back?

In a fan-forced oven the element sits around the fan at the rear, so the back is always the hottest point if air is not moving. Check that the fan turns, that trays are not pushed against the rear panel and that the oven is not overloaded. Turning the tray halfway through cooking helps in any oven.

Can I use a universal door seal?

Universal seal kits exist, but the fit depends on the length, profile and clip positions matching your oven. A seal made for your model number is the more reliable choice and avoids gaps at the corners.

Melbourne repairers for ovens & cooktops

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

DP Electric

Mobile service

12 Brodribb Rd, Clyde North VIC 3978

In-home repairs of dishwashers, washing machines, dryers, fridges, ovens, cooktops and rangehoods.

Services south-east Melbourne, the eastern suburbs, Bayside and the Mornington Peninsula.

RapidFix Solutions

Mobile service

113 East St, Hadfield VIC 3046

On-site repairs of ducted gas and reverse-cycle heating, split system, ducted and evaporative cooling, domestic fridges and freezers, washing machines, dryers, dishwashers, ovens and cooktops.

Services Glenroy, Coburg, Brunswick, Pascoe Vale, Essendon and other suburbs.

See all ovens repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More ovens guides