Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Electric oven not heating: what to check before you call a repairer

Easy15–30 minutesReviewed By the MelbourneFix team

The short answer

Check the clock and the switchboard first: an oven left in automatic timer mode, or with a tripped breaker, will not heat even though nothing is broken. If those are fine, a blown element is the most likely fault, and replacing it in a hardwired oven is a job for a licensed person.

An electric oven is a simple machine. One or more heating elements warm the cavity, a thermostat switches them on and off to hold the temperature, and on a fan-forced oven a fan at the back moves the hot air around. When the oven stays cold, either power is not reaching the elements or an element has burnt out.

A good share of ovens that appear dead have nothing wrong with them. A clock that was knocked into automatic mode, or that reset itself after a power cut, will stop the oven heating until it is set again. It is the first thing a repairer checks, and you can check it for free.

The steps below take you through the settings and the power supply, then show you how to recognise a failed element, fan or thermostat by sight and sound. They stop at diagnosis. Built-in ovens are hardwired to the house wiring, so the repair itself belongs to a licensed electrician or a licensed appliance technician.

Likely causes, most common first

  • Clock or timer in automatic mode, or not set after a power cut

    DIY

    The display is flashing, or shows AUTO, an A or a small pot symbol. The light and fan may work but nothing gets hot. Very common on older ovens.

  • Tripped circuit breaker or wall switch turned off

    DIY

    No clock, no light, no fan. The oven is completely dead, sometimes after another appliance tripped the power.

  • Wrong function selected, or demonstration or lock mode active

    DIY

    Light and fan run but there is no heat. The function dial is on light or defrost, or the display shows a key symbol or a demo message.

  • Blown heating element

    Professional

    One function still heats and another does not, or the oven takes far longer to preheat. You may see a blister, split or burnt spot on the element, and the failure may have tripped the safety switch.

  • Fan motor failed (fan-forced ovens)

    Professional

    No fan noise on a fan-forced setting, or a scraping or squealing noise. Food burns at the back and stays pale at the front.

  • Faulty thermostat, temperature sensor or selector switch

    Professional

    Oven heats but never reaches temperature, overheats badly, or the thermostat light never switches off. Elements look intact.

Before you start

Safety first

  • Do not remove an element, the rear panel inside the oven or any cover that exposes wiring. In Victoria, disconnecting or reconnecting a hardwired appliance must be done by a licensed electrician, or by an appliance technician holding a Restricted Electrical Worker's licence for like-for-like repairs. Energy Safe Victoria's position is that electrical work is not a DIY job.
  • Before you put your hands inside the oven to look at an element, turn the oven off, switch off its circuit breaker at the switchboard and wait until the oven is completely cold.
  • A damaged element can be live even when it is not glowing. Look, but do not touch a blistered or split element with anything metal.
  • If the oven trips the safety switch, leave it off. Do not keep resetting the switch to finish cooking dinner.
  • A burning plastic or fishy electrical smell, or scorch marks around the controls, means turn the oven off at the switchboard and leave it off.

What you will need

  • Torch
  • The oven's user manual, or the model number from the rating plate inside the door frame so you can look the manual up
  • Oven thermometer (optional, useful if the oven heats but poorly)
  • Pen and paper to note any error code

Step-by-step checks

  1. Step 1: Check the clock and timer

    Look at the display. If the time is flashing, the oven has lost power at some point and many models will not heat until the time of day is set again. Set the clock using the instructions in your manual and try the oven.

    If the display shows AUTO, a letter A or a cooking-pot symbol, the oven thinks it has been programmed to start or stop at a set time. On many ovens you return to manual by pressing the button marked with a hand symbol, or by pressing two of the timer buttons together. Ovens with a round analogue clock usually have a small inner knob that you turn until the indicator points to the hand symbol or the word manual.

    The exact method differs between brands, so use the manual for your model. Most manufacturers publish them online, and the model number is on a plate around the door frame.

    Tip: If the oven stopped working straight after a blackout or after someone cleaned the control panel, the clock is the likely answer.

  2. Step 2: Check the wall switch and the switchboard

    Some kitchens have an isolating switch for the oven on the wall, often near the cooktop or inside an adjacent cupboard. Make sure it is on.

    Then go to the switchboard. The oven normally has its own circuit breaker, usually labelled oven or stove. If it has tripped, the lever will be down or sitting in a middle position. Push it fully off, then on.

    Reset it once only. If the breaker or the safety switch trips again when the oven is turned on, something inside the oven is faulty, most often an element leaking current to earth. Leave it off and go to the call-a-repairer list below.

    Careful: A breaker that trips repeatedly is doing its job. Resetting it over and over can overheat damaged wiring.

  3. Step 3: Check the function and temperature dials

    Turn the function selector to plain fan-forced or conventional bake and set the temperature to 180 degrees Celsius. The light-only and defrost positions run the lamp and fan without any heat, and they sit right next to the cooking positions on most dials.

    On ovens with a touch panel, look for a key or padlock symbol, which means the child lock is on, and for a demo or showroom message, which lets the display work with the elements disabled. Your manual explains how to cancel both.

    If a dial spins freely or no longer clicks into its positions, the knob may have split on its shaft. Pull it off and check. A cracked knob is a cheap part and a fair DIY swap, because nothing electrical is disturbed.

  4. Step 4: Test each function and watch what happens

    Select the grill and set it to high. Within two or three minutes the top element should glow red along its full length. Then switch to a bake or fan-forced setting and feel for warmth at the door after five minutes.

    Note which functions heat and which do not. A grill that works alongside a fan-forced setting that blows cold air points to the rear fan element. An oven that heats on fan-forced but will not grill points to the top element. This is exactly the information a repairer wants when you ring.

    Watch the thermostat indicator light as well. It should come on when you set a temperature and go out once the oven is up to heat. A light that never comes on suggests the thermostat or selector switch is not calling for heat.

  5. Step 5: Inspect the elements with the power isolated

    Turn the oven off, switch its breaker off and let the oven go cold. Take the shelves out and use a torch to look along the grill element in the roof of the oven. On older ovens you can also see the bake element on the floor. Many newer ovens hide the lower element under the floor panel, and the fan element sits behind the rear panel, so you will not be able to see those.

    A failed element usually shows it. Look for a blister or bulge in the metal sheath, a split or hole, a burnt or white powdery patch, or a section that has sagged. Any of those means the element is finished, even if part of it still glows.

    Do not unscrew the element or the rear panel to get a better look. What you have seen is enough for a repairer to bring the right part.

  6. Step 6: Listen for the fan

    With the power back on, choose a fan-forced setting and listen at the door. You should hear a steady whirr from the back of the oven, and with the light on you can usually see the fan blades turning behind the rear grille. On some ovens the fan pauses while the door is open, so check with the door closed.

    If the fan is silent or noisy, stop using fan-forced settings. Without moving air the rear element overheats its own corner of the oven, and a thermal cut-out may shut the heat down altogether.

    Do not confuse this with the cooling fan, which blows air out near the door or control panel and keeps running after you turn the oven off. That one is normal.

When to stop and call a repairer

  • The breaker or safety switch trips whenever the oven, or one particular function, is turned on.
  • You can see a blistered, split, sagging or burnt element.
  • One function heats and another does not after you have ruled out the clock and the settings.
  • The fan-forced fan is silent, slow or noisy.
  • The oven overheats, never reaches temperature, or the thermostat light stays on permanently.
  • There is a burning smell, a melted knob, or scorch marks near the controls or the door.

In Victoria, disconnecting or reconnecting a hardwired oven or cooktop must be done by a licensed electrician or a technician with a restricted electrical licence. Gas appliances must be repaired by a licensed gasfitter. You can check electrical licences with Energy Safe Victoria and gasfitters with the Building and Plumbing Commission.

What it costs

Doing it yourself
$0 for the checks. A replacement control knob is a low-cost part if yours has cracked.
Professional repair
$220–$480 for an oven element replaced and fitted. A call-out or diagnostic fee of $80–$200 is common and is often credited against the repair.

Indicative ranges from 2026 Australian cost guides, not Melbourne quotes. Thermostat, fan motor and control board repairs vary widely by brand, so ask for a firm quote after diagnosis. See our Melbourne repair cost guide for more.

Repair or replace?

An element is a wearing part and replacing one is routine. On an oven that is otherwise sound, with a door that seals and controls that work, the repair is nearly always worth doing because it costs a fraction of a new oven plus installation.

The sums change when the fault is an electronic control board on an older oven, when parts are no longer available, or when the oven has several problems at once, such as a failed element, a perished door seal and worn hinges. Remember that a replacement oven also needs a licensed electrician to connect it, and that it has to fit the existing cabinet cut-out, which is not identical across brands.

If the oven is only a few years old, talk to the retailer before paying for a repair. Under the Australian Consumer Law an oven must last a reasonable time, which can be longer than the manufacturer's warranty, and the remedy comes from the business that sold it.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Why did my oven stop working after a power outage?

Most likely the clock. Many ovens will not heat while the time is flashing or while the timer sits in automatic mode. Set the time of day and return the timer to manual, following your manual, and the oven should work again.

The oven light and fan work but there is no heat. What does that mean?

Power is reaching the oven, so the breaker is fine. Check the timer mode and the function dial first. If those are right, the element for that function has probably failed, or the thermostat is not switching it on.

Can I replace an oven element myself?

Not in a hardwired oven. The element connects directly to mains wiring, and in Victoria that work must be done by a licensed electrician or an appliance technician with a Restricted Electrical Worker's licence. Your part of the job is the diagnosis, which shortens the visit.

Why does my oven trip the safety switch?

Usually because an element has cracked and is leaking current to earth, sometimes only once it warms up. Moisture after heavy cleaning can do it too. Leave the oven off at the breaker and have it tested.

Can I keep using the grill if the main oven element has failed?

If the element simply stopped heating and nothing trips, the other functions are generally usable in the short term. If you can see damage on any element, or the safety switch has tripped, stop using the oven until it is repaired.

Melbourne repairers for ovens & cooktops

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

DP Electric

Mobile service

12 Brodribb Rd, Clyde North VIC 3978

In-home repairs of dishwashers, washing machines, dryers, fridges, ovens, cooktops and rangehoods.

Services south-east Melbourne, the eastern suburbs, Bayside and the Mornington Peninsula.

RapidFix Solutions

Mobile service

113 East St, Hadfield VIC 3046

On-site repairs of ducted gas and reverse-cycle heating, split system, ducted and evaporative cooling, domestic fridges and freezers, washing machines, dryers, dishwashers, ovens and cooktops.

Services Glenroy, Coburg, Brunswick, Pascoe Vale, Essendon and other suburbs.

See all ovens repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More ovens guides