Gas cooktop won't ignite: clicking, no clicking and what each one means
The short answer
Lighting a gas burner takes three things at the same moment: gas coming out of the burner, a spark from the little ceramic-cased electrode beside it, and a clear path between the two. Most ignition problems come from the third one. A pot boils over, water and starch get under the burner cap, and the spark either shorts out or cannot reach the gas.
The first thing to notice is the sound. Clicking with no flame means the ignition works and the trouble is at the burner. No clicking on any burner means the ignition system has no power. A flame that lights and then dies when you let go of the knob is the flame-failure device doing its job.
Everything in this guide is cleaning, drying, reseating parts that are designed to lift off, and checking power. That is where a householder's part ends. Gas work is not DIY in Victoria, and the section on what to do if you smell gas applies before anything else.
Likely causes, most common first
Wet or dirty burner and electrode
DIYClicking but no flame, or a weak spark, often on one burner after a boil-over or after the cooktop was wiped down.
Burner cap or crown not seated properly
DIYBurner lights on one side only, the flame is lopsided or lifts, or it stopped lighting straight after cleaning.
Blocked flame ports
DIYGaps in the ring of flame, or the burner lights at the far side with a small pop after a delay.
No power to the ignition
DIY or professionalNo clicking on any burner, yet every burner lights normally with a match or gas lighter.
Flame-failure device not sensing the flame
DIY or professionalBurner lights while the knob is held in and goes out the moment you release it.
Failed ignition switch, spark module or gas supply fault
ProfessionalOne knob does not trigger a spark while the others do, clicking never stops, or there is no hiss of gas at any burner.
Before you start
Safety first
- If you smell gas: turn the cooktop off, do not operate light switches, power points or anything that could spark, and do not light a flame. Open doors and windows. If it is safe to reach, turn the gas off at the meter, or at the cylinder valve if you are on LPG. Then go outside and call your gas distributor's emergency line, which is printed on your gas bill, or 000.
- Do not attempt any work on gas connections, hoses, jets or regulators. Gas cooktops are Type A gas appliances and must be serviced or repaired by a licensed gasfitter. Gasfitters in Victoria are licensed by the Building and Plumbing Commission, and Energy Safe Victoria is the gas safety regulator.
- If a burner has not lit after a few seconds, turn the knob off and wait at least a minute for the gas to clear before trying again.
- Let the cooktop cool fully before lifting off trivets and burner parts. Cast iron holds heat for a long time.
- Never bypass or wedge a flame-failure device so the burner stays on without it.
What you will need
- Old toothbrush
- Dry cloth or paper towel
- Warm water and dishwashing detergent
- Pin, needle or straightened paper clip (for the flame ports only)
- Torch
Step-by-step checks
Step 1: Work out which problem you have
Turn one burner knob to the ignition position and listen. Then try each of the other burners. You are sorting the fault into one of three groups: clicking with no flame, no clicking at all, or a flame that will not stay lit.
Note whether one burner or all of them are affected. One misbehaving burner is almost always dirt, moisture or a misplaced cap on that burner. All burners at once points to something shared: the power to the ignition, or the gas supply.
If nothing lights and you cannot hear or smell any gas at the burner, check whether other gas appliances in the house work, such as the hot water. If they are out too, look at whether the valve at the gas meter is open, or whether the LPG cylinder is empty. If you cannot find an obvious reason, call your gas retailer or a gasfitter.
Step 2: Dry out a wet burner
If the trouble began after a spill or a clean, moisture is the first suspect. With the cooktop cold, lift off the trivet, the burner cap and the burner crown underneath it. Dry each piece thoroughly, and dab the electrode and the well it sits in with paper towel.
Leave the parts off for an hour or so in a warm kitchen to finish drying, then reassemble and try again. Water trapped in the crown or under the knobs can take a while to evaporate.
Continuous clicking after a clean, even with all the knobs off, is usually water in the ignition switches behind the knobs. Switch the cooktop's power point off and let it dry overnight. If the clicking is still there the next day, a switch has probably failed.
Tip: When cleaning a gas cooktop, wring the cloth out well and avoid spraying cleaner directly at the burners or the base of the knobs.
Step 3: Clean the burner parts and the electrode
Wash the caps and crowns in warm water with dishwashing detergent and scrub the slots with an old toothbrush. Check the manual before putting them in the dishwasher, because aluminium crowns tend to discolour and pit.
Clear each flame port, the row of small slots or holes around the crown, with a pin or a straightened paper clip. Rinse and dry completely.
The electrode is the small white ceramic post with a metal tip beside the burner. Brush it gently with a dry toothbrush to remove baked-on grease. It is brittle, so do not lever against it. A cracked ceramic lets the spark escape sideways and the electrode will need replacing.
Careful: Clean only the removable parts and the flame ports. Do not poke anything into the brass jet in the centre of the burner base and do not unscrew it. Enlarging or damaging a jet changes how much gas flows, and that is gasfitter work.
Step 4: Refit the crown and cap correctly
Each crown has lugs or notches that line up with the base, and on most cooktops one of them sits around the electrode. Lower the crown on and turn it slightly until it drops into place and no longer rocks.
Then sit the cap on top so it is flat and centred. A cap that is tilted or sitting on the wrong sized burner sends gas out unevenly, so the spark has nothing to light and the flame, if it catches, is yellow and ragged. On cooktops with several burner sizes, make sure the caps have not been swapped around.
Light the burner and look for an even ring of steady blue flame.
Step 5: Check the power to the ignition
No clicking anywhere means the spark module is not being powered. Most gas cooktops have a lead that plugs into a power point in the cupboard underneath or beside the oven. Check that the plug is fully in and the power point is switched on, and test the power point with a lamp or phone charger.
Some cooktops and freestanding cookers use a battery for ignition instead. The manual will show where the battery holder is. Fit a fresh battery of the same type.
Check the switchboard for a tripped breaker or safety switch as well. If the power point is live and there is still no spark at any burner, the spark module or its wiring has failed and needs a technician.
Tip: Most gas cooktops can be lit with a long match or gas lighter during a power cut. Check your manual first, and hold the flame at the burner before you turn the gas on.
Step 6: Test the flame-failure device
Many cooktops have a flame-failure device: a thin metal probe beside each burner that sits in the flame. It only allows gas to keep flowing while it is hot. That is why these cooktops need the knob pushed in and held for several seconds after the flame appears.
If the burner goes out when you release the knob, hold it in for longer, around ten seconds, and make sure the knob is pushed fully down. Then check that the probe is clean and that the flame actually touches it. Grease on the probe, or a crooked cap that steers the flame away, will stop it warming up. Wipe the probe gently with a dry cloth once the cooktop is cold.
If the flame still dies with a clean probe and a properly seated burner, the device or its valve has failed. Do not try to adjust or bend the probe. Book a gasfitter.
When to stop and call a repairer
- You smell gas at any time other than the brief moment of lighting. Follow the gas smell procedure first.
- There is no gas at any burner and you cannot find an obvious reason such as a closed meter valve or an empty LPG cylinder.
- The flame is mostly yellow or orange, leaves soot on pots or lifts off the burner after you have cleaned and reseated everything.
- A burner will not stay lit with a clean flame-failure probe and a correctly fitted cap.
- The igniter clicks continuously after a full day of drying, or one knob never triggers a spark.
- An electrode is cracked, loose or missing its metal tip, or the power point is live and there is no spark at any burner.
In Victoria, disconnecting or reconnecting a hardwired oven or cooktop must be done by a licensed electrician or a technician with a restricted electrical licence. Gas appliances must be repaired by a licensed gasfitter. You can check electrical licences with Energy Safe Victoria and gasfitters with the Building and Plumbing Commission.
What it costs
- Doing it yourself
- $0 in most cases. A fresh battery if your cooktop uses one for ignition.
- Professional repair
- A call-out or diagnostic fee of $80–$200 is typical, often credited against the repair. Parts and labour for electrodes, ignition switches or flame-failure parts vary by brand, so ask for a quote.
Indicative figures from 2026 Australian cost guides, not Melbourne quotes. Confirm that the person you book holds a gasfitting licence if the repair goes beyond the ignition electrics. See our Melbourne repair cost guide for more.
Repair or replace?
Ignition faults are seldom a reason to replace a cooktop. Electrodes, ignition switches and spark modules are small parts, and a cooktop with sound burners and valves will usually carry on for years after one is replaced.
Replacement is worth pricing when the cooktop is old enough that parts have been discontinued, when knobs and valves have become stiff or loose, or when the enamel and burner bases are corroded. Fitting a new gas cooktop requires a licensed gasfitter, who should give you a compliance certificate for the work, and some households use that moment to compare the cost of moving to induction, which needs an electrician and often a new circuit.
For a cooktop that is only a few years old, raise the fault with the seller first. The Australian Consumer Law expects appliances to last a reasonable time, which can extend past the manufacturer's warranty.
Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.
Common questions
Why does my gas cooktop keep clicking after it has lit?
Usually moisture or grease in the ignition switch behind a knob, which keeps the spark circuit closed. Turn the power point off and let the cooktop dry out overnight. If the clicking returns when the power is restored, the switch needs replacing.
Is it safe to light the burner with a match while the igniter is not working?
On most cooktops, yes, and manuals generally describe how. Light the match or gas lighter first, hold it at the burner, then turn the gas on low. If your cooktop has a flame-failure device you will still need to hold the knob in for several seconds.
Why does the flame go out when I let go of the knob?
The flame-failure device has not warmed up enough to hold the gas valve open. Hold the knob in for around ten seconds, and check that the probe beside the burner is clean and sitting in the flame. If that does not fix it, the device needs a gasfitter.
One burner lights and the others do not. Is that a gas problem?
Unlikely. If one burner gets gas and lights, the supply is fine. Burners that fail individually are nearly always dirty, damp or have a cap out of position. Clean and reseat each one.
What colour should the flame be?
Blue and steady, sometimes with a small yellow tip. A flame that is mostly yellow or orange, or that leaves black marks on pots, is not burning properly. Clean and refit the burner parts, and if the colour does not improve, stop using that burner and call a gasfitter.
Melbourne repairers for ovens & cooktops
Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.
WAM Electrical
Shopfront & mobile50A Hartnett Dr, Seaford VIC 3198
Repairs washing machines, dryers, fridges, dishwashers, ovens and cooktops across Melbourne and sells appliance spare parts.
SOS Appliance Melbourne
Mobile serviceSuite 96, 211 High St, Thomastown VIC 3074
In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.
Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.
DP Electric
Mobile service12 Brodribb Rd, Clyde North VIC 3978
In-home repairs of dishwashers, washing machines, dryers, fridges, ovens, cooktops and rangehoods.
Services south-east Melbourne, the eastern suburbs, Bayside and the Mornington Peninsula.
RapidFix Solutions
Mobile service113 East St, Hadfield VIC 3046
On-site repairs of ducted gas and reverse-cycle heating, split system, ducted and evaporative cooling, domestic fridges and freezers, washing machines, dryers, dishwashers, ovens and cooktops.
Services Glenroy, Coburg, Brunswick, Pascoe Vale, Essendon and other suburbs.
This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.
More ovens guides
Electric oven not heating: what to check before you call a repairer
Electric oven cold or slow to heat? Check the clock, the switchboard and the function dial, then learn the signs of a blown element or a failed thermostat.
Oven cooking unevenly or losing heat: door seal, hinges and temperature checks
Cakes burnt on one side, or heat pouring out around the oven door? How to inspect and replace a clip-in door seal and check the oven's real temperature.