Whipper snipper won't start or won't feed line: how to fix both
The short answer
Whipper snippers cause two quite separate kinds of frustration. One is the engine that will not start, or starts and dies as soon as you touch the throttle. The other is a machine that runs perfectly but will not feed any line out of the head, so you spend the afternoon stopping to pull it out by hand.
Most petrol trimmers are two-stroke. They have no separate oil supply, so the engine is lubricated by oil mixed into the petrol. That makes them more sensitive to fuel than a four-stroke mower. The mix goes stale quickly, and the wrong ratio or straight petrol does real damage.
This guide takes the engine first and the cutting head second. The line feed section applies equally to battery and corded electric trimmers, which use the same kind of bump-feed head.
Likely causes, most common first
Stale fuel or the wrong mix
DIYTrimmer has sat for a couple of months or more with fuel in it. It will not fire, or it starts and bogs down under throttle. Fuel smells flat or sour.
Flooded engine or wrong starting sequence
DIYStrong fuel smell, fuel dripping from the muffler or carburettor, a wet spark plug. Usually follows many pulls with the choke left on.
Fouled spark plug or blocked air filter
DIYHard starting that has crept up over time, loss of power, smoky running. Plug tip is black and oily, and the filter is caked with dust and clippings.
Line welded, tangled or wound incorrectly on the spool
DIYEngine runs well but bumping the head brings out no line, or the line snaps off inside the head. Opening the head shows turns stuck together or crossed over.
Wrong line diameter or a worn bump head
DIYLine jams in the eyelets or pours out unchecked. Bump knob is worn through or flat on one side, the spring is missing or the eyelets are grooved.
Blocked carburettor, fuel filter or perished fuel lines
ProfessionalFresh fuel and a new plug make no difference. Primer bulb does not fill, stays collapsed or is cracked, or fuel lines are hard, split or weeping.
Before you start
Safety first
- Stop the engine and pull the spark plug lead off before touching the cutting head. On a battery trimmer remove the battery, and on a corded one unplug it at the power point.
- Mix and pour fuel outdoors with the engine cold, away from any flame or spark. Use a proper fuel container and wipe up spills before starting the engine.
- Take stale fuel in a sealed container to a council transfer station or household chemical collection that accepts it. Do not tip it on the ground or into a drain.
- Wear eye protection, long trousers and enclosed shoes when running the trimmer, including for a quick test. The line throws stones.
- Never run the trimmer with the guard removed. The guard also carries the small blade that cuts the line to length.
- The muffler stays hot for some time after the engine stops. Let it cool before working near it.
What you will need
- Fresh regular unleaded petrol and two-stroke oil, with a measuring bottle or marked mixing container
- Sealable fuel container for the old mix
- Spark plug spanner and a new plug of the type in the manual
- Replacement trimmer line of the diameter specified for your head
- Side cutters or strong scissors
- Clean rag and a soft brush
- Safety glasses and gloves
Step-by-step checks
Step 1: Drain old fuel and mix a fresh batch
Two-stroke mix deteriorates faster than straight petrol. If the fuel in the tank or the can is more than a month or two old, replace it. Tip or siphon the old mix into a sealable fuel container for disposal.
Mix new fuel in a clean container, not in the trimmer's tank. Use fresh regular unleaded and a two-stroke oil made for air-cooled engines. The correct ratio is printed on the fuel cap, on a sticker on the machine or in the manual. Common ratios are 25:1 and 50:1 depending on the engine, and they are not interchangeable, so follow the one for your machine and measure the oil rather than estimating it. Shake the container to mix before filling the tank.
A small number of trimmers have four-stroke engines with a separate oil filler. Those take straight unleaded, and the oil level needs checking instead. If you are not sure which you have, look for an oil dipstick or check the manual before fuelling.
Tip: Mix only what you will use in a month or so. A litre goes a long way in a trimmer.
Careful: Never run a two-stroke on straight petrol, even briefly. Without oil in the fuel the engine can seize within minutes.
Step 2: Follow the cold start sequence exactly
Small two-strokes are particular about starting. The usual sequence is: switch to on, choke fully closed, press the primer bulb until you can see fuel in it and it feels firm, usually around six to ten presses, then pull the cord until the engine fires or coughs once.
As soon as it coughs, move the choke to half or off as your manual directs and pull again. Leaving the choke fully on after that first cough is the most common way to flood the engine.
If the primer bulb never fills with fuel, is cracked, or stays squashed flat after pressing, fuel is not reaching the carburettor. That means a perished bulb, split fuel line or blocked in-tank filter, and it is a workshop job for most owners.
Step 3: Clear a flooded engine
If you smell fuel and the engine will not catch, stop pulling. Set the choke to off, hold the throttle wide open and pull the cord several times to push air through the engine. It will often fire on the fourth or fifth pull and run roughly for a few seconds before clearing.
If it still will not start, remove the spark plug, dry it, leave the engine open for 15 minutes, then refit the plug and start with the choke off.
Step 4: Check the spark plug and air filter
Pull the plug lead off and unscrew the plug. Two-stroke plugs run dirtier than four-stroke ones, so some dark colour is normal, but a tip that is wet, caked in black carbon or has a worn electrode should be replaced. A new plug is under $15. Fit the type listed in the manual, start it by hand to avoid cross-threading, and tighten it snugly.
Open the air filter cover, which usually unclips without tools. Brush off a felt or paper filter, or replace it if it is clogged. Wash a foam filter in warm soapy water, rinse it and let it dry completely before refitting.
Step 5: Open the head and find out why the line will not feed
With the plug lead off or the battery out, press in the tabs on the side of the head or unscrew the bump knob, following the arrow moulded into it, and lift out the spool. Note how the spring and spool sit so they go back the same way.
Look at the line on the spool. If turns have melted together, that is line welding, caused by heat when the head is run hard against fences and edges or with the line too short. If turns are crossed over one another, the line was wound loosely or unevenly and has locked itself. In either case pull off the damaged line and discard it.
Clean the grass and dirt out of the head and check the parts. The bump knob should be intact, not worn through. The spring should be present and springy. The metal or plastic eyelets where the line exits should be smooth, not cut into sharp grooves. Worn parts are sold as spares, and a complete replacement head is available for most trimmers.
Step 6: Rewind the spool properly
Use line of the diameter specified for your head. It is marked on the head, the spool or in the manual. Line that is too thick jams in the eyelets and overloads small trimmers. Line that is too thin snaps and welds more easily. A new pack costs a few dollars.
Cut the length the manual specifies. Do not be tempted to fit extra, because an overfilled spool jams. For a twin-line spool, fold the line at its midpoint and hook the fold into the slot in the spool's centre divider, or feed each end into its anchor hole, depending on the design.
Wind in the direction of the arrow on the spool, keeping the line tight and laying each turn neatly beside the last, with the two lines in their own channels and never crossing. Stop with about 15 centimetres of each line free and park the ends in the holding notches on the spool rim.
Feed the ends through the eyelets, seat the spool on its spring, refit the cover until every tab clicks, then pull the lines to free them from the notches. Run the trimmer and tap the head on the ground. Each bump should release a short length, and the blade on the guard trims it.
Tip: Trimmer line dries out and turns brittle with age, especially stored in a hot shed. Keep spare line out of the sun, and replace line that snaps every few minutes.
When to stop and call a repairer
- The engine will not start, or will not rev, on fresh correctly mixed fuel with a new plug and a clean air filter. The carburettor or fuel system needs attention.
- The primer bulb is cracked or will not fill, or fuel lines are split or leaking.
- The starter cord is jammed, will not retract, or the engine feels locked when you pull. It may have seized, particularly if it was run on unmixed petrol.
- The trimmer runs but the head does not spin, or the shaft vibrates heavily. The drive shaft, clutch or gearbox needs inspection.
- The engine starts but loses power as it warms up and you have ruled out fuel. A carbon-clogged exhaust screen is likely and is best cleaned by a workshop.
Stop using any battery pack that is swollen, cracked, leaking or getting hot. Charge on a hard surface with the supplied charger, not overnight or unattended, and take old packs to a B-cycle drop-off point. They must never go in household bins.
What it costs
- Doing it yourself
- Usually under $40: a few dollars for trimmer line, under $15 for a spark plug, plus fresh petrol and a small bottle of two-stroke oil.
- Professional repair
- We do not have reliable published figures for trimmer repairs. For context, a basic service on a four-stroke push mower is roughly $50–$100, and small-engine workshops price trimmer work on a similar hourly basis.
Indicative only. Ask for a quote before work starts, because a carburettor rebuild with new fuel lines on a low-cost trimmer can approach the price of a new one. See our Melbourne repair cost guide for more.
Repair or replace?
Line, spools, bump heads, plugs and filters are cheap and worth replacing on any trimmer. A line feed problem is never a reason to replace the machine.
The fuel system is where the sums change. On a good-quality trimmer, a workshop carburettor clean and new fuel lines are worthwhile. On an entry-level trimmer, get a quote first and compare it with the price of a replacement. An engine that has seized from running without oil is usually not economic to repair.
If you are replacing it, consider how you use it. For a typical suburban block, a battery trimmer on the same battery platform as your other tools avoids fuel mixing and stale fuel altogether. Battery and corded electric trimmers are e-waste in Victoria and cannot go to landfill. Drain the fuel from a petrol trimmer before taking it to a transfer station.
Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.
Common questions
What fuel mix does my whipper snipper need?
The ratio set by the engine's manufacturer, which is printed on the fuel cap, on the machine or in the manual. 25:1 and 50:1 are both common and depend on the engine, so do not assume. If you cannot find it, search the model number for the manual rather than guessing.
Why does the line keep welding itself together inside the head?
Heat. Running the head hard against paving, fences and thick growth, or letting the line get very short, heats the spool until the turns fuse. Wind the line tightly and evenly, use the right diameter, keep the line at its full length, and let the tips of the line do the cutting.
It starts fine but dies when I squeeze the throttle. What is wrong?
Check that the choke is fully off once the engine has warmed for a few seconds. If it is, the engine is being starved of fuel under load, which points to stale fuel, a blocked fuel filter or a carburettor that needs cleaning. Try fresh mix first.
Which way do I wind the line?
Follow the arrow moulded into the spool. If the arrow has worn away, check the manual or the diagram on a replacement spool for your model rather than guessing. Line wound the wrong way will not feed when you bump the head.
Can I use thicker line so it lasts longer?
Only up to the maximum diameter listed for your trimmer. Thicker line is heavier and puts more load on the engine or motor, and it may not pass through the eyelets or fit on the spool. On small battery and electric trimmers in particular, stay with the specified size.
Melbourne repairers for lawn mowers & power tools
Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.
Mowers and More
Shopfront5/23 Cooper St, Campbellfield VIC 3061
Services and repairs mowers, ride-ons, generators, pumps, trimmers and chainsaws regardless of where they were bought, for brands including Honda, Stihl, Victa, Rover, Masport, Cub Cadet and Briggs & Stratton.
Second workshop in Diamond Creek.
Melbourne Power Tools & Repairs
Shopfront268-272 High St, Preston VIC 3072
Repairs pneumatic, cordless and electric power tools and carries out warranty repairs for power tool brands.
Essendon Mowers
Shopfront561 Keilor Rd, Niddrie VIC 3042
Services lawn mowers, ride-on mowers, brushcutters, blowers, chainsaws and small engines, and sharpens chainsaw chains.
B.W. Machinery
ShopfrontMultiple service centres · South-east
Workshop servicing and repair of lawn mowers, ride-on mowers, chainsaws, brushcutters and other outdoor power equipment.
Service centres in Bentleigh East, Cheltenham, Seaford and Ringwood.
This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.
More garden & tools guides
Lawn mower won't start: step-by-step checks for petrol and battery mowers
Petrol mower will not start after winter? Check for stale fuel, the spark plug, air filter, oil and safety bail before paying for a service. Battery tips too.
Cordless tool battery not charging: what the charger is telling you
18V drill, blower or trimmer battery will not charge? Read the charger lights, check temperature and contacts, and test with a second pack before replacing it.