Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Cordless tool battery not charging: what the charger is telling you

Easy15–30 minutes, plus cooling or warming timeReviewed By the MelbourneFix team

The short answer

A charger that refuses a lithium tool battery is usually protecting it: the pack is too hot, too cold, or has been run too flat. Let it reach room temperature, clean the contacts and try a second battery or charger to find which part has failed. Never open a pack or try to jump-start it.

The slide-on lithium-ion batteries used across 18V-style drills, blowers, hedge trimmers and line trimmers are not simple containers of charge. Each pack has a small circuit board that monitors cell voltage and temperature, and the charger talks to it before it sends any current. If either side is unhappy with what it sees, charging does not start.

That is why a battery can appear dead when it is only too hot from a hard session with the blower, and why a pack left flat in the shed for a year may never charge again. The charger's lights are the best evidence you have, so the first job is to read them properly.

There is very little to repair on a battery pack, and nothing inside it that is safe to work on at home. What you can do is work out whether the battery, the charger or the conditions are at fault, which tells you what to replace or claim under warranty.

Likely causes, most common first

  • Battery too hot or too cold

    DIY

    Charger shows a waiting or temperature delay signal straight after heavy use, on a hot day, or on a cold winter morning in an unheated shed. Charging begins by itself later.

  • Dirty or damaged contacts, or battery not fully seated

    DIY

    No lights or intermittent lights that change when you wiggle the pack. Contacts look dull, dusty or have sawdust and grit packed around them.

  • Deeply discharged pack locked out

    Professional

    Battery was left flat for months, or left in a tool. Charger shows a fault signal immediately or does nothing, and the battery's own gauge shows no lights.

  • Worn-out or faulty battery

    DIY or professional

    Pack is several years old, run time has been shrinking, or it charges to full in a few minutes and then goes flat almost at once. A second battery charges normally.

  • Faulty charger or power supply

    DIY or professional

    No lights at all with any battery, or the same fault with every battery. Charger lead is damaged, or the power point is dead.

Before you start

Safety first

  • Stop using and stop charging any battery that is swollen, cracked, dented, leaking, overheating, smells unusual or makes a hissing sound. Move it outside, away from anything that can burn, if it is safe to do so.
  • If a battery catches fire or starts venting smoke, get away from it and call 000. The smoke is toxic.
  • Use only the charger supplied for that battery system or one the manufacturer lists as compatible. A charger that physically fits is not necessarily compatible.
  • Charge on a hard, non-combustible surface such as a concrete floor or a bare bench with clear space around it. Not on a bed, couch or carpet, and not unattended or overnight.
  • Let a battery cool down after use before putting it on the charger.
  • Never open a battery pack, and never try to revive one by connecting it to another battery, a power supply or a car charger.
  • Never put lithium batteries in household rubbish or recycling bins. They cause fires in trucks and at depots.

What you will need

  • Clean dry cloth
  • Cotton buds and a little isopropyl alcohol
  • Torch
  • A second battery or charger from the same system, borrowed if need be
  • The charger's manual or the light code label on the charger itself
  • Proof of purchase, in case it becomes a warranty claim

Step-by-step checks

  1. Step 1: Read the charger lights against the label

    Light codes are not standard between brands, so do not guess. Nearly every charger has a small legend printed on its label, and the manual has the full table. Look at what the charger does with no battery fitted, then what it does when you slide the pack on.

    In general terms, most chargers distinguish four states: charging, fully charged, a temperature delay where the charger is waiting for the pack to cool down or warm up, and a fault where it has rejected the pack. Which colour and flash pattern means which varies, so match it to the legend for your charger.

    Press the gauge button on the battery as well. A pack that shows some charge but will not accept more points you in a different direction from one that shows nothing.

    Tip: Take a short video of the flashing pattern on your phone. It is easier to compare with the manual, and useful if you end up talking to the retailer or the manufacturer.

  2. Step 2: Confirm the charger has power

    If the charger shows no lights at all, plug something else into the same power point to check it is live, and try the charger in another power point. Garage and shed power points are often on a circuit that has tripped at the switchboard.

    Inspect the charger's lead and plug for cuts, crushing or scorch marks. Do not use a charger with a damaged lead.

  3. Step 3: Let the battery reach room temperature

    Lithium cells must not be charged when they are very hot or close to freezing, and the charger enforces this. As a general guide, most will not charge a pack that is below about 0 degrees or above roughly 40 to 45 degrees Celsius. The exact limits are in your manual.

    A battery straight off a blower or mower on a summer afternoon is often above that upper limit. Take it off the charger, bring it indoors and leave it on a hard surface for 30 minutes or more. Do the same in reverse for a pack that has been in a cold shed on a winter morning. Then try again.

    Some chargers begin charging automatically once the temperature is in range. Others need the pack removed and refitted.

    Careful: Do not cool a battery in the fridge or freezer or warm it with a heater or hair dryer. Let it come to room temperature naturally.

  4. Step 4: Clean the contacts and reseat the pack

    Unplug the charger at the power point. Shine a torch into the slots on the battery and at the metal terminals on the charger. Sawdust, plaster dust, grass clippings and corrosion all get in the way.

    Brush or blow out loose debris, then wipe the metal contacts with a dry cloth or a cotton bud barely dampened with isopropyl alcohol. Let it evaporate fully. Do not scrape the contacts with a knife or sandpaper, and do not bend the terminals.

    Plug the charger back in and slide the battery on firmly until it seats. A pack that sits a couple of millimetres short will not make contact.

  5. Step 5: Swap in a second battery or charger

    This is the test that settles it. Put a second battery from the same system on your charger. If that one charges, your charger is fine and the first battery is the problem. If neither charges, suspect the charger.

    If you have only one of each, a neighbour or relative with the same brand can help, and so can the retailer's service desk. Some hardware stores will check a battery on a display charger if you ask.

    Only ever test with batteries and chargers from the same manufacturer's system. Adaptors and off-brand chargers muddy the result and bring their own risks.

  6. Step 6: Check the warranty before buying a replacement

    Tool batteries commonly carry their own warranty period, which may be different from the tool's and sometimes depends on online registration. Find the receipt and check the date.

    Under the Australian Consumer Law a battery must also last a reasonable time for what it cost, and that can extend beyond the manufacturer's warranty. The remedy comes from the seller, so take the battery, charger and proof of purchase back to where you bought it. A pack that fails within its first couple of years of ordinary home use is worth raising.

  7. Step 7: Dispose of a dead pack properly

    If the battery is finished, cover its terminals with clear sticky tape and take it to a B-cycle battery drop-off point. Many hardware stores, supermarkets and council sites host them. Check the B-cycle website for a location near you that accepts power tool batteries.

    A swollen, leaking or otherwise damaged battery should not go into a drop-off bin. Keep it outside, away from the house and anything combustible, and contact your council for advice on where to take it.

When to stop and call a repairer

  • The battery is swollen, leaking, cracked, has been dropped hard or got hot enough to be uncomfortable to hold. Stop using it and do not charge it again.
  • The charger shows a fault for a battery that is at room temperature with clean contacts, and a second battery charges normally. Take the faulty pack to the retailer or the manufacturer's service agent.
  • The charger shows no lights on a known good power point, or its lead is damaged.
  • The battery was run flat and left for months, and the charger now rejects it. Do not try to wake it up yourself.
  • The battery, charger or tool has been wet, or smells of burning.

Stop using any battery pack that is swollen, cracked, leaking or getting hot. Charge on a hard surface with the supplied charger, not overnight or unattended, and take old packs to a B-cycle drop-off point. They must never go in household bins.

What it costs

Doing it yourself
$0 for the checks. A replacement battery runs from roughly $50 for a small house-brand pack to $250 or more for a high-capacity pack from a trade brand.
Professional repair
There is generally no repair route for a domestic tool battery. The practical options are a warranty or consumer guarantee claim through the seller, or a new battery or charger.

Battery prices are general retail observations and move with promotions. Check the price of a kit that includes a tool, battery and charger, which is sometimes close to the price of a battery alone. See our Melbourne repair cost guide for more.

Repair or replace?

Batteries are consumables. After some years and a few hundred charge cycles a pack holds noticeably less, and eventually the charger rejects it. If the tools are in good order, a new genuine battery is the sensible fix and the tools carry on.

Look at the system as a whole before buying. If the platform has been discontinued, or you only own one tool on it, the cost of a new battery may be better put towards a kit on a current platform. If you own several tools that share the battery, replacing the pack is clearly worthwhile.

Be wary of very cheap unbranded replacement packs and of services offering to re-cell an old pack. The protection circuit and cell quality are what keep a lithium battery safe, and neither is easy to verify on an unknown product.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Can I jump-start a dead lithium tool battery?

No. Videos show people forcing charge into a locked-out pack from another battery or a power supply. The lockout exists because cells that have been over-discharged can be internally damaged, and charging damaged cells can cause a short circuit and fire, sometimes days later. Replace the pack or claim on the warranty.

How should I store tool batteries?

Indoors or in a cool, dry spot out of direct sun, off the charger and out of the tool. A partial charge of around half is better for long storage than completely full or flat. Check them every few months and top up so they do not drift down to empty. A hot shed, a ute tray or a car boot in summer shortens their life.

Is it bad to leave the battery on the charger?

Modern chargers stop charging when the pack is full, but fire services advise against leaving lithium batteries charging unattended or overnight, and that advice applies here. Take the battery off once it is charged and switch the charger off at the power point.

Why does my battery go flat so quickly now?

Capacity fades with age, heat and the number of charge cycles. Cold weather also reduces run time temporarily. If a pack that once ran a blower for 20 minutes now manages five, it is near the end of its life, and no amount of cycling will bring it back.

Can I use another brand's charger or an adaptor?

Stick to the charger made for your battery system. Brands use different communication between the pack and charger, and an adaptor can bypass the temperature and voltage checks that keep charging safe. Using non-approved chargers may also affect a warranty claim.

Melbourne repairers for lawn mowers & power tools

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Mowers and More

Shopfront

5/23 Cooper St, Campbellfield VIC 3061

Services and repairs mowers, ride-ons, generators, pumps, trimmers and chainsaws regardless of where they were bought, for brands including Honda, Stihl, Victa, Rover, Masport, Cub Cadet and Briggs & Stratton.

Second workshop in Diamond Creek.

B.W. Machinery

Shopfront

Multiple service centres · South-east

Workshop servicing and repair of lawn mowers, ride-on mowers, chainsaws, brushcutters and other outdoor power equipment.

Service centres in Bentleigh East, Cheltenham, Seaford and Ringwood.

See all garden & tools repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More garden & tools guides