Dishwasher not draining: how to clear the filter, hose and sink waste
The short answer
At the end of each stage of a cycle, a small pump in the base of the dishwasher pushes the dirty water through a filter, along a corrugated hose and into the waste pipe under your kitchen sink. If the water cannot get through any one of those points, it stays in the bottom of the machine.
First, check that there really is a problem. A little clean water sitting in the sump, below the level of the filter, is normal and keeps the pump seals wet. What is not normal is cloudy water covering the floor of the tub, a machine that stops mid-cycle with a drain error, or dirty water appearing in the dishwasher after you empty the sink.
Food scraps, broken glass, grease and labels soaked off jars cause most blockages, and most of them can be reached from inside the tub or the cupboard under the sink. The steps below go in that order and stop before any panels come off.
Likely causes, most common first
Clogged filter or sump
DIYGreasy, gritty water sitting over the base of the tub. Dishes have been coming out dirtier for a while.
Kinked, squashed or sagging drain hose
DIYStarted after the machine was installed or moved, or after something was pushed into the cupboard under the sink. Sink water may run back into the dishwasher.
Blocked sink waste or dishwasher spigot
DIY or professionalThe kitchen sink is also slow to empty or gurgles when the dishwasher pumps out. Grease and food build up where the hose joins the waste.
Blanking plug left in a new waste fitting
ProfessionalThe dishwasher has never drained since a new sink, waste trap or dishwasher was fitted. The pump runs but no water leaves at all.
Drain pump jammed or failed
ProfessionalFilter and hose are clear. The pump hums or buzzes without moving water, or makes no sound at the drain stage.
Interrupted cycle or control fault
DIY or professionalDoor was opened mid-cycle or the power went off. Or a drain error code keeps returning with no blockage to be found.
Before you start
Safety first
- Switch the dishwasher off at the power point and unplug it before putting your hands in the sump. The power point is usually in the cupboard next to the machine.
- If you cannot find a plug, the dishwasher may be hardwired. Turn it off at its isolating switch or the switchboard, and leave disconnecting it to a licensed electrician or a technician with a restricted electrical licence.
- Broken glass collects in the filter and sump. Wear rubber gloves and feel around carefully rather than sweeping your fingers through.
- If the cycle has just stopped, the water and the element in the base can be hot. Give it 20 minutes to cool.
- Do not pull the dishwasher out from under the benchtop yourself if doing so means disconnecting plumbing or wiring.
What you will need
- Rubber gloves
- Old towels, a sponge and a jug or cup for bailing
- Torch
- Old toothbrush or soft dish brush
- Bucket or washing-up bowl
- Dish detergent and warm water (for washing the filter in the sink)
Step-by-step checks
Step 1: Run the drain or cancel function and listen
A cycle that was interrupted by a power cut, or by someone opening the door and not pressing start again, will leave water behind. Close the door firmly and use the cancel, reset or drain function. On many machines this means holding the start button for about three seconds. The manual will confirm it for your model.
Listen for the pump. A steady hum and the sound of water running into the sink waste means the machine can drain and the cycle was simply cut short. A hum with no water moving points to a blockage. Silence points to the pump or its control.
Tip: Note any error code on the display before you switch off. A repairer will ask for it, along with the model number from the label on the edge of the door.
Step 2: Bail out the water and clean the filter
Switch off and unplug. Slide out the bottom basket and bail the water with a cup, then sponge out the rest so you can see what you are doing.
The filter sits in the floor of the tub, usually under the lower spray arm. Most are a cylinder that unlocks with a quarter turn anticlockwise and lifts out, with a flat metal mesh plate underneath that lifts out after it. Wash both in the sink with warm soapy water and a brush until the mesh is clear when held up to the light.
Step 3: Check the sump under the filter
With the filter out, shine a torch into the well it sits in. This is where glass chips, fruit pips, toothpicks, bits of bone and jar labels end up. Lift out anything you find, wearing gloves.
Some machines have a small clip-off cover in the sump that gives access to the drain pump impeller, and the manual will show it if yours does. If so, remove the cover and check that the little paddle wheel turns and has nothing wound around it. If the manual does not show a user-removable cover, do not lever at anything down there.
Refit the mesh plate and lock the cylinder filter back in properly. A filter that is not seated lets debris straight through to the pump.
Step 4: Follow the drain hose under the sink
Open the cupboard under the sink and find the corrugated drain hose coming through from the dishwasher. Straighten any kinks and move bottles, bins and anything else that is squashing it.
The hose should rise in a loop to the underside of the benchtop, as high as it can go, before it drops to its connection on the waste pipe. This is called a high loop, and it stops water from the sink running back down the hose into the dishwasher. If the hose has fallen and lies along the cupboard floor, lift it and secure it up high with a cable tie or a saddle clip.
Step 5: Test the sink waste
The dishwasher and the sink share a waste pipe, so a partly blocked sink will stop the dishwasher draining. Fill the sink with a few centimetres of water and pull the plug. It should empty quickly and quietly. If it drains slowly, gurgles or pushes water up into the second bowl, the blockage is in the kitchen plumbing.
The drain hose pushes onto a small side branch on the sink trap, called a spigot. Grease and food pulp tend to set hard just inside it. A sink that runs freely while the dishwasher cannot pump out at all suggests the spigot itself is choked. Clearing the trap and spigot is a job for a plumber if you are not confident with it or if anything is glued or sealed.
Step 6: If the sink or waste is new, suspect the blanking plug
New sink traps and waste fittings are sold with the dishwasher spigot closed off by a moulded plug or cap, so that houses without a dishwasher do not leak. Whoever connects a dishwasher is supposed to remove it. It is forgotten surprisingly often.
If the machine has not drained once since a new sink, tap, waste fitting or the dishwasher itself went in, this is the most likely cause. Go back to the plumber or installer who did the work and ask them to check the spigot. It takes them a few minutes to put right.
Step 7: Run a short test cycle
Plug the machine back in and run a rinse or quick program with the baskets empty. Stay nearby for the first drain and listen at the cupboard under the sink for water rushing through the waste.
When it finishes, open the door and check the tub floor. If the water has gone, run a hot cycle with a dishwasher cleaner to shift the grease that caused the trouble. If the water is still there and you have ruled out everything above, the pump or its wiring needs a repairer.
When to stop and call a repairer
- The filter, sump, hose and sink waste are all clear but the pump only hums, or makes no sound when it should be draining.
- The pump makes a loud grinding or rattling noise, which usually means glass in the impeller that you cannot reach.
- The same drain error code returns after you have cleaned everything and run the reset.
- The dishwasher trips the safety switch when it reaches the drain stage.
- The machine has never drained since new plumbing was fitted. Call the plumber or installer back to check for a blanking plug.
- The dishwasher is hardwired or has to be pulled out from under the benchtop to go any further.
Switch the dishwasher off at the power point before reaching into the sump. Tightening a hose by hand is fine, but changes to the plumbing or a hardwired connection are work for a licensed plumber or electrician.
What it costs
- Doing it yourself
- $0. Cleaning the filter, clearing the sump and re-routing the hose need no parts. A dishwasher cleaner for the follow-up hot cycle costs a few dollars at the supermarket.
- Professional repair
- $200–$420 for a typical dishwasher repair such as a drain pump, including the call-out. A control board replacement is more, usually $350–$800.
Indicative ranges from Australian cost guides, not Melbourne quotes. A call-out fee of $80–$200 is common and is often credited against the repair if you go ahead. See our Melbourne repair cost guide for more.
Repair or replace?
A drain problem by itself is rarely terminal. Most are blockages that cost nothing to clear, and a replacement drain pump is a modest repair on a machine that washes well.
The sums change if the quote is for a control board on an older or entry-level dishwasher. When the repair approaches half the price of an equivalent new machine, and the racks are rusting or the door seal is tired, replacement is usually the better use of the money.
A dishwasher that is only a few years old should not need a new pump. Under the Australian Consumer Law an appliance must last a reasonable time, which can be longer than the manufacturer's warranty, so speak to the retailer before paying for a repair. An old dishwasher is e-waste in Victoria and cannot go to landfill. Council transfer stations take them, and many retailers remove the old machine when they deliver the new one.
Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.
Common questions
Is it normal to have some water in the bottom of the dishwasher?
A small amount in the sump, below the filter, is normal and is there by design. Water that covers the floor of the tub, or that is dirty and smells, means the last drain did not finish.
Why does dirty sink water come up into my dishwasher?
The drain hose has no high loop, or the sink waste is partly blocked. Without a loop rising to the underside of the benchtop, water from the sink can run down the hose into the machine. Lift and secure the hose, and check the sink drains freely.
Can I use drain cleaner in a dishwasher?
No. Caustic drain cleaners can damage the pump seals, hoses and stainless steel, and they leave residue where your dishes are washed. Clear the blockage by hand, and use a product sold as a dishwasher cleaner for routine maintenance.
How often should I clean the dishwasher filter?
Rinse it every week or two if you use the machine daily, and wash it properly with a brush once a month. If you do not scrape plates before loading, check it more often.
My dishwasher drains but smells bad. Is that related?
Often it is. A sagging drain hose holds stagnant water, and a greasy filter and sump do the rest. Clean the filter, fix the high loop and run a hot cycle with a dishwasher cleaner. Leaving the door slightly open between washes also helps the tub dry out.
Melbourne repairers for dishwashers
Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.
Woolley Appliance Services
Shopfront & mobile10 Freight Rd, Ravenhall VIC 3023
Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.
Authorised Samsung and LG service centre. Second workshop in Clayton.
WAM Electrical
Shopfront & mobile50A Hartnett Dr, Seaford VIC 3198
Repairs washing machines, dryers, fridges, dishwashers, ovens and cooktops across Melbourne and sells appliance spare parts.
SOS Appliance Melbourne
Mobile serviceSuite 96, 211 High St, Thomastown VIC 3074
In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.
Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.
DP Electric
Mobile service12 Brodribb Rd, Clyde North VIC 3978
In-home repairs of dishwashers, washing machines, dryers, fridges, ovens, cooktops and rangehoods.
Services south-east Melbourne, the eastern suburbs, Bayside and the Mornington Peninsula.
This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.
More dishwashers guides
Dishwasher not cleaning properly: fixes for dirty, gritty or cloudy dishes
Dishes coming out gritty, greasy or cloudy? Check the spray arms, filter, loading, detergent and rinse aid, and what Melbourne's soft water means for dosing.
Dishwasher leaking water: how to find where it is coming from
Water on the floor in front of the dishwasher, or a flood error such as Bosch E15? Check the door seal, detergent, levelling and hoses before you call.