Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Dishwasher leaking water: how to find where it is coming from

Moderate30–60 minutesReviewed By the MelbourneFix team

The short answer

Most dishwasher leaks come from a dirty door seal, suds from the wrong detergent, or a machine that is not level. If water is collecting in the base and triggering the anti-flood system, the source needs to be found, not just tipped out.

A dishwasher throws water around the inside of the tub at pressure for an hour or more, so it does not take much of a gap for some to escape. Water that appears at the front, under the door, usually comes from the door area: the seal, the level of the machine or foam pushing out. Water that appears at the side or in the cupboard next door usually comes from a hose connection.

There is a third kind of leak that you may never see on the floor. Most modern dishwashers have a tray in the base that catches internal leaks, with a float switch that shuts off the water supply and runs the drain pump when the tray gets wet. The machine stops and shows a flood warning. On Bosch and its sister brands the code is E15.

The checks below deal with what you can see and reach. They do not involve pulling the machine out or removing its panels, because that is where the mains wiring and plumbing connections are.

Likely causes, most common first

  • Dirty or damaged door seal

    DIY or professional

    Drips or a small puddle at the front corners or along the bottom of the door. Greasy grime on the seal and along the lower edge of the door.

  • Wrong detergent or over-sudsing

    DIY

    Foam visible in the tub or bubbling out under the door. Often follows hand dishwashing liquid getting into the machine, or a rinse aid spill.

  • Machine not level or poorly loaded

    DIY

    Water runs out at the front during the wash. The machine tips forward when the baskets are pulled out, or a large tray sits against the door.

  • Loose or damaged inlet or drain hose connection

    DIY or professional

    Water in the cupboard under the sink or at the side of the machine, with the area in front of the door dry.

  • Split spray arm or blocked filter

    DIY

    A leak that started suddenly at the door. A cracked arm fires a jet straight at the door seal, and a choked filter can let the water level rise.

  • Internal leak into the base tray

    Professional

    Machine stops with a flood or leak error such as E15, and the drain pump runs continuously. There may be no water on the floor at all.

Before you start

Safety first

  • Switch the dishwasher off at the power point and unplug it before investigating a leak. If water has reached the power point or you cannot get to it safely, turn the circuit off at the switchboard first.
  • Turn off the tap that supplies the dishwasher, usually under the sink, if there is any sign of water from the inlet hose or if the machine is showing a flood warning.
  • If the dishwasher is hardwired, it must be disconnected by a licensed electrician or a technician with a restricted electrical licence. Do not pull it out yourself.
  • Mop up promptly. Water on a kitchen floor is a slip hazard, and water left under cabinetry swells the kickboards and carcasses.
  • Do not keep running a machine that trips the safety switch or shows a flood error.

What you will need

  • Old towels and a sponge
  • Torch
  • Soft cloth and an old toothbrush
  • Warm water and a little dish detergent or white vinegar
  • Spirit level, or a level app on your phone
  • Dry paper towel (to trace drips)

Step-by-step checks

  1. Step 1: Find out where the water appears

    Dry the floor completely. Lay dry paper towel along the front of the machine and inside the cupboard under the sink, around the hoses and the tap. Run a short program and check the towels every ten minutes or so.

    Wet at the front under the door points to the seal, levelling, loading or suds. Wet under the sink points to a hose connection or the waste. Wet at the side or underneath with nothing obvious at the front suggests a leak inside the cabinet. Note at what point in the cycle it happens: filling, washing or draining.

  2. Step 2: Clean and inspect the door seal

    Open the door and look at the rubber seal around the top and sides of the tub opening, and at the separate strip along the bottom of the door or the lower front lip of the tub. The bottom edge is not washed by the spray and collects a line of grease and food that holds the seal off its seat.

    Wipe the seals and the metal faces they close against with a cloth and warm soapy water or diluted white vinegar. Use an old toothbrush in the corners. Do not use bleach or abrasive pads on the rubber.

    Run a fingertip along the seal for splits, hard flattened sections or places where it has pulled out of its channel. A seal that is simply dislodged can be pressed back in. A split or hardened seal needs replacing.

    Tip: Check that the door latches firmly and sits square to the cabinet. A door that has dropped on one side, or that needs a shove to latch, will leak even with a new seal.

  3. Step 3: Rule out suds

    Open the door mid-cycle and look. The water in a dishwasher should be almost free of foam. A tub full of suds will push out past the door seal and can get into the base of the machine.

    The usual cause is hand dishwashing liquid. It gets in when someone uses it in place of dishwasher detergent, when dishes are soaked or pre-washed in it and loaded without rinsing, or when it is used to wash the filter and not rinsed off. Spilt rinse aid does the same thing, so wipe up any overflow after refilling the dispenser.

    To clear suds, cancel the cycle and let it drain, then run rinse programs with the machine empty until no foam is left. In Melbourne's soft water, too much detergent also foams more than you would expect, so cut the dose back if you see persistent suds with the correct product.

  4. Step 4: Check the machine is level and loaded sensibly

    Put a level on the top edge of the open tub, side to side, then on the open door or a basket rail, front to back. The machine should be level or lean back very slightly. If it leans forward, water in the base of the tub sits against the bottom of the door.

    The front feet can usually be wound up or down from the front once the kick panel is lifted off or with the door open, depending on the model. Check too that the machine is fixed under the benchtop and does not tip when both baskets are pulled out.

    Look at the loading as well. A large tray or chopping board standing at the front of the lower basket can deflect the spray straight at the door seal.

  5. Step 5: Check the spray arms and filter

    Lift off the lower spray arm and unclip the upper one. Look for a split along the seam or a crack near the hub. A split arm sends a hard jet sideways, often right at the door joint, and causes a leak that seems to come from nowhere. Replacement arms are a simple part to fit.

    Clean the filter while you are there. A filter clogged with grease slows the water returning to the sump.

  6. Step 6: Inspect the hoses you can reach

    In the cupboard under the sink, find the inlet hose where it screws onto the tap. Run dry paper towel around the nut. If it is damp, turn the tap off and check the nut by hand. It should be firm, and a gentle hand-tighten is as far as you should go. If it still weeps, the washer inside has perished or the hose is failing, and that is a job for a plumber or appliance technician.

    Then check where the corrugated drain hose joins the sink waste. Look for water marks, a loose clip or a hose that has been knocked sideways by something stored in the cupboard. Run your hand along both hoses for splits or kinks as far as you can reach.

    Careful: Many inlet hoses have a bulky plastic box at the tap end. This is a safety valve that shuts off the water if the hose leaks. If it has tripped, the hose assembly needs replacing by a technician. Do not try to open or bypass it.

  7. Step 7: If the machine shows a flood error, stop there

    A flood code such as E15 on a Bosch means the float switch in the base tray has detected water. The machine shuts the inlet valve and runs the drain pump continuously, and it will usually keep doing so until the power is switched off. Turn it off at the power point and turn off the water tap.

    You will find plenty of advice to tilt the machine back to tip the water out of the tray so the float drops and the error clears. That treats the alarm, not the leak. The water got into the base from somewhere, whether a pump seal, an internal hose, the sump gasket, the door or a suds overflow, and the base tray is also where the wiring and electrical parts live. Tipping it means pulling out a heavy machine that is still connected to power and water, and running it again without finding the source risks a bigger leak and water over live components.

    If you know the cause was a one-off, such as a load of hand dishwashing liquid foaming over, tell the technician. Otherwise book a repair and leave the machine off.

When to stop and call a repairer

  • The machine shows a flood or leak error such as E15, or the drain pump runs non-stop even when the machine is empty.
  • Water is coming from underneath or from the side with nothing leaking at the door or the hose connections you can see.
  • The inlet hose or its connection keeps weeping after a hand-tighten, or the safety valve on the hose has tripped.
  • The door seal is split or hardened, or the door has dropped and no longer latches squarely.
  • The dishwasher trips the safety switch. Leave it switched off until it has been checked.
  • The machine is hardwired or has to come out from under the benchtop to trace the leak.

Switch the dishwasher off at the power point before reaching into the sump. Tightening a hose by hand is fine, but changes to the plumbing or a hardwired connection are work for a licensed plumber or electrician.

What it costs

Doing it yourself
$0 for cleaning the seal, clearing suds and levelling. Door seals and spray arms are priced by model, so get the model number from the label on the door edge and ask a spare parts supplier.
Professional repair
$200–$420 for a typical dishwasher repair including the call-out, which covers most seal, hose and pump leaks. A control board damaged by water is more, typically $350–$800.

Indicative ranges from Australian cost guides, not Melbourne quotes. A call-out fee of $80–$200 is common and often credited against the repair. Ask for a quote once the source of the leak has been found. See our Melbourne repair cost guide for more.

Repair or replace?

Door seals, hoses and pump seals are worthwhile repairs on most dishwashers. Getting a leak fixed early is also much cheaper than repairing a swollen kitchen cabinet or a lifted floor.

Replacement becomes the better option when the tub itself has rusted through or cracked, or when water has damaged the control board on a machine that is already eight to ten years old. If a quote is more than about half the price of an equivalent new dishwasher, get the new price before deciding.

If the machine is fairly new, contact the retailer first. Under the Australian Consumer Law an appliance must last a reasonable time, which can be longer than the manufacturer's warranty, and the remedy comes from the seller. A dishwasher that is being replaced is e-waste in Victoria and cannot go to landfill, so use the retailer's removal service or a council transfer station.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

What does E15 mean on a Bosch dishwasher?

It means water has collected in the base tray under the tub and lifted the anti-flood float. The machine stops filling and runs the drain pump to protect your kitchen. The code tells you there is a leak inside the machine, not where it is, so the source still has to be found.

I used hand dishwashing liquid in the dishwasher by mistake. What now?

Cancel the cycle and let the machine drain. Scoop out as much foam as you can, wipe up anything on the floor, then run rinse programs with the machine empty until the suds are gone. It can take three or four runs. If the machine stops with a flood error afterwards, foam has reached the base and it should be checked.

Why does my dishwasher only leak sometimes?

Intermittent leaks usually follow the load or the detergent. A large tray against the door, an overfull lower basket or an extra-foamy wash will leak on one cycle and not the next. Note what was different about the loads that leaked.

Can I replace a dishwasher door seal myself?

On many machines the main seal around the tub opening simply presses into a channel and can be changed by hand with the power off, using the correct part for your model. The lower door seal is often fixed behind the inner door panel, and we recommend leaving that one to a repairer.

Is a small drip from the dishwasher worth worrying about?

Yes. A slow leak under a built-in dishwasher soaks into the chipboard kickboard and cabinet sides long before you notice it on the floor. Find the source early, while it is still a cheap fix.

Melbourne repairers for dishwashers

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Woolley Appliance Services

Shopfront & mobile

10 Freight Rd, Ravenhall VIC 3023

Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.

Authorised Samsung and LG service centre. Second workshop in Clayton.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

DP Electric

Mobile service

12 Brodribb Rd, Clyde North VIC 3978

In-home repairs of dishwashers, washing machines, dryers, fridges, ovens, cooktops and rangehoods.

Services south-east Melbourne, the eastern suburbs, Bayside and the Mornington Peninsula.

See all dishwashers repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More dishwashers guides