Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Dishwasher not cleaning properly: fixes for dirty, gritty or cloudy dishes

Easy30–45 minutesReviewed By the MelbourneFix team

The short answer

Poor wash results usually come from blocked spray arm jets, a dirty filter, bad loading or the wrong detergent dose, not a broken machine. In Melbourne's soft water, using too much detergent is a more common mistake than using too little.

A dishwasher cleans with three things: water thrown hard from rotating spray arms, detergent, and heat. It reuses the same few litres of water over and over during each stage, straining it through a filter as it goes. If the jets are blocked, the filter is dirty, the detergent is not dissolving or the water is not getting hot, the results drop off quickly.

The type of mess left behind is a useful guide. Grit and specks redeposited on glasses in the top basket point to the filter. Whole patches of dried-on food in one area of a basket point to a blocked or obstructed spray arm. A greasy film suggests low temperature or old detergent. A white haze on glasses is a dosing problem, and in Melbourne it is usually the opposite of what people expect.

Almost all of this can be fixed at the kitchen sink with a toothpick and a brush. The checks below take about half an hour.

Likely causes, most common first

  • Dirty filter

    DIY

    Fine grit or food specks on glasses and in the bottoms of cups, mostly in the top basket. Water in the sump looks greasy.

  • Blocked or obstructed spray arms

    DIY

    One basket or one corner comes out dirty while the rest is clean. A tall item or pan handle is stopping an arm from turning.

  • Poor loading

    DIY

    Bowls nested together, large trays shielding other items, or the detergent door blocked so the tablet is found half dissolved after the cycle.

  • Wrong detergent dose, stale detergent or no rinse aid

    DIY

    White film or cloudiness on glasses, gritty powder residue, or dishes that come out wet and spotty.

  • Cycle too short or too cool for the load

    DIY

    Quick or eco programs leave baked-on or greasy items dirty. An intensive program cleans the same load properly.

  • Water not heating or circulation pump weak

    Professional

    Dishes are cold and wet at the end of a full cycle, the tablet is barely dissolved, or the spray sounds weak. Results are poor on every program.

Before you start

Safety first

  • Switch off at the power point and unplug before removing spray arms or reaching into the sump. If the machine is hardwired, turn it off at the isolating switch or switchboard.
  • Wait for the machine to cool after a cycle. The element in the base and any water left in the sump can be hot.
  • Watch for broken glass in the filter and sump, and wear rubber gloves.
  • Dishwasher detergent is strongly alkaline. Keep tablets and powder away from children, avoid getting powder on wet skin, and never mix a dishwasher cleaner with other cleaning products.

What you will need

  • Rubber gloves
  • Toothpick or wooden skewer
  • Old toothbrush or soft dish brush
  • Torch
  • Dish detergent and warm water (for washing parts in the sink)
  • White vinegar and a cloth (for the glass test)
  • Dishwasher cleaner
  • Rinse aid

Step-by-step checks

  1. Step 1: Clean the filter

    Switch off and unplug, pull out the bottom basket and remove the filter from the floor of the tub. On most machines the cylindrical part unlocks with a quarter turn and the flat mesh plate lifts out after it.

    Scrub both parts in warm soapy water with a brush. A filter that looks clean can still be coated in a thin layer of grease that blinds the mesh, so hold it up to the light to check. Wipe out the well it sits in and refit it so that it locks firmly.

    Tip: Scrape plates into the bin but do not rinse them under the tap. Modern detergents are designed to work on food soil, and scraping is all the preparation they need.

  2. Step 2: Clear the spray arm jets

    The lower arm usually lifts straight off its hub. The upper arm, under the top basket, normally unscrews or unclips with a twist. Check the manual if either resists and do not force them.

    Hold each arm up to the light and look through the jets. Seeds, rice grains, bits of label and scale lodge in the small holes. Push them back into the arm with a toothpick, then shake the debris out through the hub opening or flush the arm under the tap. Look along the seam of each arm as well. An arm that has split open loses pressure and needs replacing, and they are an easy part to order by model number.

    Refit the arms and spin each one by hand. They should turn freely and settle without wobbling.

  3. Step 3: Fix the loading

    After loading, spin both spray arms by hand before you close the door. If a pan handle, a tall platter or a utensil that has slipped through the basket stops an arm, that whole area gets no wash.

    Face the dirty side of each item towards the centre and angle cups and bowls so that water can reach inside and drain off. Do not nest bowls or spoons together. Put large trays and chopping boards at the sides and back of the lower basket, never across the front where they block the detergent door from opening and shield everything behind them.

  4. Step 4: Sort out the detergent and rinse aid

    Use fresh detergent that has been stored dry. Powder that has gone lumpy and tablets from a damp cupboard under the sink lose much of their strength. Put the tablet in the dispenser, not loose in the tub, where it dissolves during the pre-wash and is pumped away before the main wash begins.

    Keep the rinse aid dispenser topped up even if your tablets say they include rinse aid. It helps water sheet off the dishes so that they dry without spots, which matters most for plastics and glasses.

  5. Step 5: Adjust the dose for Melbourne's soft water

    Melbourne's mains water is soft, meaning it carries very little dissolved calcium and magnesium. Soft water needs less detergent to do the same job. The dose on the packet is typically written to cover harder water as well, so with powder, try filling the dispenser about half to two-thirds full and adjust from there.

    Too much detergent in soft water causes its own problems: a white or bluish film, gritty residue, and over the years a permanent cloudiness on glassware called etching. To tell them apart, rub a cloudy glass with a cloth dipped in white vinegar. A film that wipes off is residue, and reducing the dose and using rinse aid will fix it. Cloudiness that stays is etching and cannot be reversed, but a lower dose and a cooler program will stop it getting worse on your other glasses.

    Many European dishwashers have a built-in water softener and a salt compartment. In Melbourne you generally do not need dishwasher salt. Set the machine's water hardness setting to its lowest or off position as the manual describes, which on most models also turns off the salt warning light. If the rinse aid setting is adjustable and glasses come out streaky or smeared, turn that down a step too.

  6. Step 6: Use a program hot enough for the load

    Most dishwashers in Australia are connected to the cold tap and heat their own water. Quick and eco programs save time or power by washing at lower temperatures, which is fine for lightly soiled loads but not for roasting pans or dried-on egg. Use the normal or intensive program for those and see whether the results improve.

    Open the door carefully straight after a full hot cycle finishes. The dishes and the tub should be hot and steamy. If everything is cold and wet at the end of a long program and the tablet has not fully dissolved, the machine is probably not heating, and that needs a technician.

  7. Step 7: Run a machine-cleaning cycle

    Grease and detergent residue build up in the parts you cannot see: the pipes, the pump and the inside of the spray arms. This is worse if you mostly run cool, short programs. Run the hottest program with the baskets empty and a dishwasher cleaner, following the directions on the pack.

    Repeat every month or two, and wipe the door edges and the bottom of the door seal at the same time. Those areas are not reached by the spray.

When to stop and call a repairer

  • Dishes and the tub are cold at the end of a full hot cycle, or the tablet is still mostly intact.
  • The spray sounds weak or you can hear the wash pump straining or cutting in and out, with the filter and arms clean.
  • The detergent dispenser door does not open during the cycle even when nothing is blocking it.
  • The machine fills with very little water, or stops with a fill or heating error code.
  • Results are still poor on every program after you have worked through all the steps above.

Switch the dishwasher off at the power point before reaching into the sump. Tightening a hose by hand is fine, but changes to the plumbing or a hardwired connection are work for a licensed plumber or electrician.

What it costs

Doing it yourself
$0 for cleaning and reloading. Rinse aid and a dishwasher cleaner are supermarket items costing a few dollars each. A replacement spray arm is priced by model, so check with a spare parts supplier.
Professional repair
$200–$420 for most dishwasher repairs including the call-out. A control board replacement is typically $350–$800.

Indicative ranges from Australian cost guides, not Melbourne quotes. Get a quote after diagnosis and ask whether the call-out fee of $80–$200 is credited against the repair. See our Melbourne repair cost guide for more.

Repair or replace?

Most cleaning complaints are fixed without spending anything, so do not start shopping until you have cleaned the filter and arms and run a hot maintenance cycle. A dishwasher that has been washing badly for months often comes back to full performance after that.

If the fault turns out to be a heating element, a wash pump or a dispenser, a repair generally makes sense on a mid-range or better machine with sound racks and seals. On a basic machine that is eight to ten years old, compare the quote against the cost of a new one, particularly if the control board is involved.

A machine that stops heating or washing properly in its first few years should be raised with the retailer. Under the Australian Consumer Law an appliance must last a reasonable time, which can be longer than the manufacturer's warranty.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Do I need dishwasher salt in Melbourne?

Generally no. Dishwasher salt regenerates the built-in softener that some machines use to treat hard water, and Melbourne's water is already soft. Set the hardness setting to its lowest level, following the manual, and the salt light should stay off. Your water retailer publishes hardness figures for your area if you want to check.

Why are my glasses cloudy?

Either detergent residue or etching. Rub the glass with white vinegar. If the film comes off, reduce your detergent dose and use rinse aid. If it does not, the surface of the glass has been etched, which is permanent and is more common in soft water with heavy detergent doses and very hot programs.

Should I rinse dishes before putting them in the dishwasher?

Scrape, do not rinse. Rinsing wastes water and gains nothing with a modern detergent. The exceptions are things a dishwasher cannot shift, such as burnt-on food, which is better soaked first.

Are tablets better than powder?

Tablets are convenient and consistent. Powder lets you adjust the dose, which is useful in soft water and for small or lightly soiled loads. Either will clean well in a machine with clear jets and a clean filter.

Why is the dishwasher tablet not dissolving?

Usually the dispenser door is blocked by a tray or tall plate in the lower basket and cannot open, or the tablet has stuck in a damp dispenser. Less often the spray arms are blocked or the water is not heating. Check the loading first, and dry the dispenser before putting the tablet in.

Melbourne repairers for dishwashers

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Woolley Appliance Services

Shopfront & mobile

10 Freight Rd, Ravenhall VIC 3023

Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.

Authorised Samsung and LG service centre. Second workshop in Clayton.

SOS Appliance Melbourne

Mobile service

Suite 96, 211 High St, Thomastown VIC 3074

In-home repairs of gas and electric ovens, gas, electric and induction cooktops, rangehoods, washing machines, dryers and dishwashers, for brands including Miele, Bosch, Fisher & Paykel, Smeg, Westinghouse, Electrolux, ASKO and ILVE.

Services northern and north-eastern suburbs including Epping, Bundoora, Preston, Heidelberg and Doncaster.

DP Electric

Mobile service

12 Brodribb Rd, Clyde North VIC 3978

In-home repairs of dishwashers, washing machines, dryers, fridges, ovens, cooktops and rangehoods.

Services south-east Melbourne, the eastern suburbs, Bayside and the Mornington Peninsula.

See all dishwashers repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More dishwashers guides