Skip to content
MelbourneFixFix it, or find someone in Melbourne who can

Dropped your phone in water? What to do in the first minutes and hours

Easy10 minutes of first aid, then 24–48 hours of dryingReviewed By the MelbourneFix team

The short answer

Switch the phone off, do not charge it, dry the outside and leave it in moving air. Skip the rice. If it went into salt water, a pool or a drink, or it will not start after drying, get it to a repairer quickly, because corrosion keeps working after the phone looks dry.

Water does not kill a phone on contact. The damage comes from two things that happen afterwards: electricity flowing through wet circuits, which causes short circuits, and corrosion, which eats at the tiny contacts and connectors over the following hours and days. Good first aid is about stopping the first and limiting the second.

That is why the first few minutes matter so much, and why the instinct to press the power button to see whether it still works is the wrong one. A wet phone that is switched off and left alone has a far better chance than a wet phone that is charged, shaken and tested.

What the liquid was matters as much as how long the phone was in it. Clean tap water is the kindest. Salt water, chlorinated pool water, soapy water, beer, soft drink and coffee all leave residue behind that keeps corroding the phone after the water itself has gone.

Likely causes, most common first

  • Brief splash or quick dip in fresh water

    DIY

    Retrieved within seconds from a sink, bath, toilet or puddle. Phone may still be working normally.

  • Moisture in the charging port only

    DIY

    Phone works but shows a liquid or moisture warning and refuses to charge by cable.

  • Muffled speaker or microphone

    DIY

    Sound is quiet or crackly after getting wet, and callers say you sound distant. Usually clears as the phone dries.

  • Salt water, pool water or a sugary or soapy liquid

    Professional

    Phone went into the sea, a pool, a washing machine or a drink. May work at first and fail days later as residue corrodes the contacts.

  • Water inside the phone

    Professional

    Fog or droplets behind the camera lens, patches under the screen, phone will not turn on, restarts by itself or gets warm while off.

  • Delayed corrosion

    Professional

    Phone seemed fine after drying, then develops charging faults, a failing camera, no sound or a dead screen over the following weeks.

Before you start

Safety first

  • If the phone was plugged into a charger when it got wet, switch the power point off first, then unplug it. Do not reach for a plugged-in phone in a sink or bath.
  • Do not charge a wet phone. Charging pushes current through a wet port and can damage the phone and the cable.
  • If the phone becomes hot, swells, hisses or smells of chemicals at any point, stop. Put it on a non-flammable surface such as concrete outside, away from anything that burns, and take it to a repairer. Do not charge or use it.
  • No ovens, microwaves, hair dryers or heaters. Heat damages the battery, softens the adhesive seals and warps the display.
  • Do not open the phone yourself. The battery is easy to puncture, and a repairer has the tools to do this safely.

What you will need

  • Lint-free cloth or paper towel
  • SIM tray ejector pin or a straightened paper clip
  • A fan, or a dry spot with good airflow

Step-by-step checks

  1. Step 1: Get it out and switch it off

    Take the phone out of the water as fast as you safely can and power it off straight away. If the screen is already black, leave it that way. Do not press buttons to check whether it works, and do not plug it in.

    If it was on charge, switch off at the power point before touching the cable.

    Careful: Resist the urge to test it. Every minute a wet phone spends switched on is a chance for a short circuit that turns a recoverable phone into a dead one.

  2. Step 2: Strip it and dry the outside

    Remove the case and any screen protector that has water trapped behind it. Eject the SIM tray and take out the SIM and any memory card. Leave the tray out, since the open slot gives moisture one more way to escape.

    Wipe the phone thoroughly with a lint-free cloth or paper towel. Hold it with the charging port facing down and tap it gently against your palm to coax water out of the port and speaker grilles. Do not shake it hard, which can spread water further inside, and do not push cotton buds or tissue into the port.

  3. Step 3: Deal with salt, chlorine and sticky liquids

    If the phone has a water resistance rating and it went into the sea, a pool or a drink, the major manufacturers advise rinsing the affected areas briefly with clean tap water and then wiping it dry. It feels wrong, but salt and sugar left to dry on the contacts do more harm than a quick fresh rinse. Use a gentle flow, not a jet.

    If the phone has no water resistance rating, is older, or has a cracked screen or back, do not add more water. Wipe it down and get it to a repairer the same day if you can. Salt water in particular starts corroding within hours.

  4. Step 4: Dry it in moving air and leave it alone

    Stand the phone upright with the port facing down in a dry room, ideally in the breeze of a fan. Moving room-temperature air is the best drying tool most households have. A sunny windowsill or the car dashboard is not suitable, because the heat does its own damage.

    Give it at least 24 hours, and 48 if it was fully submerged or you can see fog behind the camera lens. Silica gel sachets in a sealed container do no harm, but they are slower than airflow.

    Tip: Skip the bag of rice. Rice draws very little moisture out of a sealed phone, it leaves starch dust and the odd grain in the ports, and the phone dries faster sitting in open air. Apple specifically advises against it.

  5. Step 5: Power on, then test charging

    After the drying time, check the ports and camera lenses for any sign of moisture. If it all looks dry, switch the phone on. If it starts, leave the charger alone for a little longer and check the basics first: screen, touch, both cameras, speaker, microphone and buttons.

    When you do connect a cable, watch for a liquid or moisture warning. If one appears, unplug and give the phone several more hours. A wireless charger is a safer way to get some charge in while the port finishes drying, provided the phone itself is dry and working normally.

  6. Step 6: Back up as soon as it works

    Treat a phone that has survived a dunking as living on borrowed time until proven otherwise. Run a full backup to the cloud or a computer on the first day, and check that your photos have finished uploading.

    Corrosion can take days or weeks to break a connection, so a phone that works today may not next month. A backup made now is free. Data recovery from a dead phone is slow, uncertain and can be expensive.

  7. Step 7: Watch it for the next few weeks

    Keep an eye out for fog inside the camera, charging that cuts in and out, a battery that suddenly drains fast, a warm back, or a screen that develops patches. Any of these means liquid got inside and the phone needs to be opened and cleaned by a repairer.

    Be especially alert to swelling or heat. A battery that has been wet can fail later. If the back or screen starts to lift, stop using and charging the phone.

When to stop and call a repairer

  • The phone was in salt water, pool water or any sticky or soapy liquid, even if it seems to be working.
  • It will not switch on after 48 hours of drying, or it switches on and restarts repeatedly.
  • You can see moisture or fog behind the camera lens or under the screen.
  • The phone gets warm while switched off, swells, or smells odd. Move it somewhere non-flammable and do not charge it.
  • The phone holds photos or other data that are not backed up anywhere. Say so at the start, because it changes how a repairer approaches the job.
  • Faults appear in the days or weeks afterwards, such as unreliable charging, no sound or camera errors.

A repairer who accepts a device that stores your data must give you a written repair notice warning that data may be lost. Take that seriously. Back up to iCloud, Google or a computer before any repair, and remove your SIM and any memory card.

What it costs

Doing it yourself
$0. Airflow and patience are the whole method.
Professional repair
Liquid damage assessment, cleaning and data recovery vary widely with the model and how far the corrosion has gone, so ask for a quote and whether there is an assessment fee. If the battery needs replacing afterwards, independents charge roughly $109–$149 for most phones.

Indicative battery range from 2026 Australian cost guides. Many repairers quote liquid damage work in stages, with an assessment first and no guarantee of success, so ask what you pay if the phone cannot be saved. See our Melbourne repair cost guide for more.

Repair or replace?

A professional liquid damage clean is worth paying for when the phone is fairly recent, when it holds data you have not backed up, or when it went into something other than clean water. The repairer opens the phone, disconnects the battery and cleans the board and connectors, which is the only way to actually stop corrosion.

For an older or low-cost phone that will not start, the economics often point the other way, particularly if all your data is safely in the cloud. A liquid-damaged phone that has been revived can also remain less reliable than it was, and a repairer should tell you that honestly.

Manufacturer warranties generally exclude liquid damage, and phones carry internal indicators that change colour on contact with liquid. If a phone sold as water resistant has failed after ordinary exposure within its stated rating, you can still raise it with the seller under the Australian Consumer Law, though expect to be asked about the circumstances. Check any care plan or contents insurance too, since accidental liquid damage is commonly covered there.

Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.

Common questions

Does putting a wet phone in rice work?

Not usefully. Rice absorbs very little moisture from inside a sealed phone, and phones left in open air with a fan dry faster. Rice dust and broken grains can also lodge in the charging port. People believe in it because phones that would have survived anyway spent a day switched off in the rice, and being switched off is what saved them.

My phone is rated IP68. Why did water still get in?

IP ratings are measured on new phones in still, fresh water in a laboratory, for a set depth and time. IP67 means up to one metre for 30 minutes, and IP68 means deeper, with the depth set by the manufacturer. The rating does not cover salt water, chlorine, soap, steam or water under pressure, and the seals weaken with age, heat, drops and any repair that opens the phone. A three-year-old phone with a few knocks should be treated as splash resistant only.

How long should I wait before turning my phone back on?

At least 24 hours in moving air for a brief dunking in fresh water, and 48 hours if it was submerged for longer or you can see fog behind the camera. If it went into salt water or a drink, do not wait and hope. Take it to a repairer as soon as you can.

Can data be recovered from a water-damaged phone that will not turn on?

Often, but not always. Phone storage is encrypted and tied to the phone's own main board, so the usual method is for a repairer to clean and repair the board well enough to start the phone and copy the data off. Success depends on how quickly the phone was switched off and how far the corrosion has gone. Before paying for recovery, sign in to your iCloud or Google account from another device, because your photos and contacts may already be there.

Can I use a hair dryer or leave the phone in the sun to speed things up?

No. Heat can damage the battery and the display and loosen the adhesive that seals the phone, and a hair dryer can push water further inside. Room-temperature air from a fan is the fastest safe option.

Melbourne repairers for phones & tablets

Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.

Fixspot Repair Centre

Shopfront

207/125 Swanston St, Melbourne VIC 3000

Repairs iPhones, iPads, Apple Watch, MacBooks, Samsung Galaxy phones and tablets, Microsoft Surface devices and phones from Google Pixel, Oppo, Xiaomi, Motorola and Nokia.

Second store in Point Cook.

City Phones

Shopfront

148 Elizabeth St, Melbourne VIC 3000

Repairs iPhone, Samsung, Google Pixel, Oppo and other phones, iPads, Samsung tablets, Apple Watch and Microsoft Surface devices, including motherboard repair and data recovery.

Also in Greensborough and St Kilda.

Mister Click

Shopfront

167 King St, Melbourne VIC 3000

Repairs iPhone, Samsung Galaxy, Google Pixel and other phones, iPads, MacBooks and laptops, and lists PlayStation and Nintendo Switch console repairs. Mail-in available.

Second location at 480 Collins St.

Phonebot Repairs

Shopfront

Shop A, 289-291 Broadway, Reservoir VIC 3073

Repairs iPhones, Samsung Galaxy phones, iPads and tablets, and Apple and Samsung smartwatches, with walk-in and mail-in options.

See all phones repairers

This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.

More phones guides