Microwave runs but does not heat: safe checks and when to replace it
The short answer
A microwave that lights up, hums and turns the plate but leaves the food cold is telling you that the low-voltage side of the oven works and the cooking side does not. Sometimes that is a setting. Often it is a failed component in the high-voltage circuit that generates the microwaves.
The honest position with this appliance is that the list of safe home checks is short. Everything you can do is from the outside or inside the cooking cavity with the oven unplugged. Nothing in this guide involves removing a screw from the outer case, and nothing should.
Work through the checks below. If they do not restore heating, you have reached the limit of what is safe, and the choice is between a technician and a new oven.
Likely causes, most common first
Wrong setting: timer, demo mode, low power or child lock
DIYDisplay counts down but there is no heat, sometimes with no usual hum. Often follows a power outage, a clean of the control panel or children pressing buttons.
Door not closing or latching properly
DIY or professionalDoor feels loose, needs a push to start, or the oven stops and starts when you press on the door. Food debris or a damaged latch hook may be visible.
Dirty or burnt waveguide cover
DIYSparking, crackling or a burning smell from one side wall of the cavity. The small flat panel on that wall is greasy, scorched or has a hole burnt in it.
Failed magnetron
ProfessionalEverything appears normal but there is no heat at all. May be accompanied by a louder than usual hum, a buzzing or a hot electrical smell.
Failed high-voltage diode, capacitor or internal fuse
ProfessionalNo heat, sometimes with a loud hum or a bang when the fault occurred. Indistinguishable from a magnetron failure without test equipment.
Faulty door interlock switch or control board
ProfessionalHeating is intermittent, cuts out mid-cycle, or depends on how the door is closed. The oven may blow its internal fuse and go completely dead.
Before you start
Safety first
- Never remove the outer cover of a microwave oven, for any reason. The high-voltage capacitor inside can hold a lethal charge long after the oven has been unplugged. Unplugging it does not make the inside safe.
- The magnetron, high-voltage diode, capacitor, transformer and door interlock switches are technician-only parts. There is no safe way to test or replace them at home.
- Do not use a microwave with a damaged door, bent hinges, a cracked door screen or a door that does not close squarely. Never try to defeat or bypass the door interlocks.
- Unplug the oven at the power point before cleaning inside the cavity or touching the waveguide cover.
- Never run a microwave empty. For any test, use a cup of water.
- If the oven sparks, smokes or smells of burning, stop it, leave the door closed, switch off at the power point and unplug it.
What you will need
- Microwave-safe cup or jug of water
- Soft cloth and mild dish detergent
- Torch
- The oven's manual, or the model number from the label inside the door frame to look it up
Step-by-step checks
Step 1: Do a proper heating test
Put a cup of cold tap water, about 250 mL, in the centre of the turntable and run the oven on high for two minutes. In a working microwave the water will be very hot, close to boiling in most ovens.
If the water is hot, the oven is fine and the earlier problem was the food, the container or the setting. If it is lukewarm, heating is weak. If it is still cold, there is no microwave output at all. Note which, because it is the first thing a technician will ask.
Careful: Take care lifting the cup out. Water heated in a microwave can be hotter than it looks.
Step 2: Check the settings
Make sure you pressed a cooking function and not the kitchen timer. On many ovens the timer counts down on the display exactly like a cooking cycle but produces no heat, and it is an easy mistake.
Check the power level has not been left on a low or defrost setting, which cycles the heating on and off and can make a short reheat seem cold.
Look for demo mode. Many ovens have a showroom mode in which the display, light and sometimes the turntable work with no heating. It is often switched on by accident with a button combination, and the way to cancel it varies by brand, so look up your model's manual. Unplugging the oven for a few minutes clears it on some models but not all.
Child lock usually stops the oven from starting at all and shows a lock symbol or the word LOCK. Holding the stop or cancel button for about three seconds releases it on many models.
Step 3: Inspect the door and latch
Open the door and look at the plastic latch hooks on the door edge and the slots they enter. Clean away any food residue from the hooks, the slots and the door seal faces with a damp cloth. Built-up grime can stop the door closing fully.
Close the door and check it sits flat and square with no gap, and that it latches with a firm click and does not rattle. Look at the mesh screen in the window for holes or damage.
If a hook is broken, the door sags on its hinges, or the oven only runs when you lean on the door, stop using it. That is not something to work around. The door and its interlocks are the main barrier between you and the microwave energy.
Step 4: Try a different power point
Plug the oven directly into a wall power point, not a power board or extension lead. A microwave draws a heavy current, and a long or light-duty lead can lower the voltage enough to affect performance.
A dead power point is not the cause when the light and turntable are working, so this check is about ruling out a poor supply. If the oven heats normally on another wall power point, have the original one looked at by a licensed electrician.
Step 5: Inspect and clean the waveguide cover
Unplug the oven. Inside the cavity, usually on the right-hand wall or the ceiling, there is a small flat rectangular panel, often silvery grey or light brown. This is the waveguide cover. It lets microwaves into the cavity while keeping food splatter out of the opening behind it.
Splattered fat on this panel carbonises, and the burnt spots then absorb energy, spark and scorch. Wipe it gently with a soft cloth dampened with warm water and a drop of detergent, then dry it. It is fragile, so do not scrub or use abrasives.
If the cover is burnt through, cracked or flaking, it needs replacing. It sits inside the cooking cavity, held by a clip or a single screw, and is the one part on a microwave that manufacturers generally treat as replaceable from inside the cavity. Buy the correct cover for your model. Do not use the oven until it is fitted.
Careful: The waveguide cover is not packaging or a piece of cardboard to be thrown away. Do not run the oven with it removed.
Step 6: Deal with sparking separately
Sparking has a short list of causes: metal in the oven such as foil, twist ties, cutlery or crockery with a metallic rim; burnt-on food on the walls or waveguide cover; a damaged waveguide cover; or chipped paint inside the cavity exposing bare metal.
Remove any metal, clean the cavity thoroughly and repeat the cup-of-water test. If it still sparks with only a cup of water inside and a clean, intact waveguide cover, stop using it. Sparking from bare or rusted metal on the cavity wall, or from behind the waveguide cover, is not a home repair.
When to stop and call a repairer
- The oven runs normally but a cup of water stays cold after two minutes on high, with the settings confirmed and demo mode ruled out.
- There is a loud hum, buzz, bang or electrical burning smell when the oven starts.
- The door is damaged, does not latch squarely, or heating depends on pressing or holding the door.
- The oven is completely dead after a bang or after the door was slammed, which suggests an internal fuse has blown for a reason.
- Sparking continues with a clean cavity, no metal inside and an undamaged waveguide cover.
- The oven trips the safety switch or a circuit breaker.
A microwave's high-voltage capacitor can hold a lethal charge long after it is unplugged. Cleaning the cavity and the waveguide cover is fine. Anything under the outer case is strictly for a technician.
What it costs
- Doing it yourself
- $0 for the settings and cleaning checks. A replacement waveguide cover is usually under $20.
- Professional repair
- We do not have reliable published figures for microwave repairs. Expect an assessment or call-out fee plus parts, and get a firm quote before agreeing to any work.
Basic benchtop microwaves sell new for roughly $100–$250, so a quote involving a magnetron or high-voltage parts will often come close to or exceed the cost of replacement. See our Melbourne repair cost guide for more.
Repair or replace?
For a standard benchtop microwave, a failed magnetron or other high-voltage part usually means replacement. The labour and parts for a technician repair are hard to justify against the price of a new oven with a new warranty.
Repair is more often worthwhile for built-in and combination microwave ovens, which cost considerably more and are sized to fit a particular cabinet cut-out. Get a quote and compare it with the cost of a replacement that fits the same space.
If the oven is fairly new, contact the retailer before doing anything else. Under the Australian Consumer Law a microwave must last a reasonable time, which can be longer than the manufacturer's warranty. A dead microwave is e-waste in Victoria and cannot go to landfill, so take it to a council e-waste collection point rather than the kerbside bin. Do not dismantle it for parts.
Not sure which way to go? Try the repair or replace calculator, and read your consumer rights before paying for a repair on something that failed early.
Common questions
Why can I not just open it up and replace the fuse or magnetron myself?
Because the high-voltage capacitor inside can store a charge capable of killing you even when the oven has been unplugged for some time. The circuit runs at several thousand volts. This is one of the few household appliances where the advice is absolute: do not remove the cover.
My microwave works but takes much longer to heat than it used to. Is it dying?
Possibly. Check the power level setting and plug it straight into a wall power point first. If a cup of water is only lukewarm after two minutes on high, the magnetron or another high-voltage part is likely weakening, and on a benchtop model that usually means replacement.
Is a microwave that is not heating dangerous to keep using?
There is no benefit in running it, and a failing high-voltage part can overheat. If the door is undamaged it is unlikely to be leaking, but unplug it and stop using it until it is repaired or replaced.
What is demo mode and how do I turn it off?
Demo mode is a showroom setting where the display and light work without any heating. The key combination to cancel it differs between brands and models, so search for your model's manual. Look for the word DEMO or a similar indicator on the display.
Can I use the microwave without the waveguide cover while I wait for a new one?
No. Without the cover, food splatter and steam enter the opening behind it and can damage the oven and cause arcing. Leave the oven unplugged until the correct replacement cover is fitted.
Melbourne repairers for coffee machines & small appliances
Independent businesses that list this kind of work. Listings are free and are not endorsements. Always confirm prices, licences and availability directly.
Service Scene Electronic Servicing
Shopfront & mobile61 Wadham Pde, Mount Waverley VIC 3149
Repairs LCD, LED, OLED and plasma TVs and monitors, audio equipment, projectors, microwaves and vacuum cleaners, by walk-in or call-out.
Authorised LG service agent that also repairs other brands.
Optimum Electronic Solutions
Shopfront & mobile31 Prime St, Thomastown VIC 3074
Repairs Samsung, LG, Hisense and Pioneer TVs, Epson projectors, soundbars and audio gear, Samsung vacuums, washing machines and dryers, Breville coffee machines and KitchenAid appliances, by mobile van or at its service centre.
Woolley Appliance Services
Shopfront & mobile10 Freight Rd, Ravenhall VIC 3023
Repairs Samsung and LG refrigerators, washing machines, dryers, dishwashers, TVs, monitors, soundbars, microwaves and vacuum cleaners, in-home or in its workshops.
Authorised Samsung and LG service centre. Second workshop in Clayton.
Chameleon Coffee
Shopfront10 Farmers Way, Point Cook VIC 3030 (drop-off by appointment)
Workshop repairing Breville espresso machines (Barista Express, Pro and Touch, Oracle, Dual Boiler, Bambino and others), Jura and De'Longhi machines, with drop-off by appointment or courier.
This guide is general information, not professional advice for your specific appliance or situation. Follow your manufacturer's manual where it differs, and read our disclaimer. Spotted an error? Tell us.
More small appliances guides
Espresso machine low pressure or no water: what to check at home
Home espresso machine dribbling, pumping no water or showing low pressure? Check the tank, priming, grind, basket and scale before paying for a repair.
Vacuum cleaner lost suction: how to find the blockage and fix it
Vacuum not picking up? Work through the bin or bag, filters, hose, brush bar and seals on corded, stick and robot vacuums, plus when a new battery makes sense.